Manuals / Fisher & Paykel / Kitchen Appliance / Dishwasher

Fisher & Paykel DishDrawer manual Problem, Possible Causes, What to Do, interior is stained

Models: DishDrawer

1 32

Download 32 pages 16.56 Kb

Page 25

interior is stained

	Problem	Possible Causes		What to Do

	interior is stained	Some foods, like tomato based products,		Pre-rinse dishes before placing in the		.
		may stain the inside of the	.	Alternatively, using the Rinse program after adding
				the dishes may minimize staining.

	Dishes did not dry	Incorrect loading.		Ensure the dishes are not nesting together.
		Rinse agent depleted.		Refill the rinse agent dispenser.
		Rinse agent setting too low.		Increase the rinse agent setting.
		Eco wash program used.		Choose a standard wash program.

	Foaming	Incorrect amount of detergent.		Refer to the detergent section or consult the
				detergent manufacturer’s instructions.
		Too much egg in the wash load.		Add detergent to the pre-rinse compartment.
		Rinse agent setting too high.		Decrease the rinse agent setting.

	No detergent dispensed	Detergent was wet when loaded.		Clean the dispenser and ensure the dispenser is dry
				when adding detergent.

	Excessive motor noise	The filter plate and/or spray arm is		Refer to the user maintenance section for details on
		incorrectly placed.		correct placement.
		No water in the motor area. This usually		Run the	through a wash program.
		occurs on the first use or when the
		has not been used for
		long periods of time.

	Water leaking	Drain hose disconnected from waste pipe.		Reconnect the drain hose to the waste pipe.
		Supply inlet hose not properly connected.		Ensure the inlet hose is connected securely.
		Other leaks.		Turn water and power supplies to the
				off. Call your Fisher & Paykel dealer or Authorized
				Service Agent.

	will not open	Childlock function is on or the Closed		Turn Lock off. Hold down the LOCK button until the
		Drawer option is on, or both.		‘lock’ symbol (prefinished models) or the green light
				(integrated models) disappears and/or press the
				POWER button to open the		.

	Intermittent beeping	is in pause mode.		Close the	and press the
				START/PAUSE button.

	Continuous beeping	A fault has occured.		Refer to the fault codes section.

23

Image 25

Fisher & Paykel DishDrawer Problem, Possible Causes, What to Do, interior is stained, the dishes may minimize staining

Contents

U S E R G U I D E Option Adjustment Mode AccessoriesUser Maintenance Instructions Trouble ShootingPREFINISHED DD603 u s e r g u i d eWhite, Brushed stainless steel Iridium stainless steel and Black INTEGRATED DD603i n t r o d u c t i o n s p e c i a l t a l e n t s o p e r a t i n g i n s t r u c t i o n s - prefinished model Press the POWER ButtonElectronic Display Load DishesCheck DELAY START MODE optionalStart PausePress the POWER Button o p e r a t i n g i n s t r u c t i o n s - integrated modelLoad Dishes Add Detergent & Rinse AidStart DELAY START MODE optionalPause Finisha. Basket a c c e s s o r i e sd. Plate Insert Cutlery Basketl o a d i n g HOW TO LOAD YOURl o a d i n g a n d a c c e s s o r i e s HOW NOT TO LOAD YOURd e t e r g e n t d i s p e n s e r when theare not suitable to be used in the Filling the Detergent Dispenserr i n s e a g e n t d i s p e n s e r Rinse Agent Indicator Lightd e t e r g e n t r i n s e a g e n t w a t e r s o f t e n e r How Much Rinse Agent to UseIdentify the setting you require for your SETTING UP THE WATER SOFTENERsoftener so that the setting corresponds to your water hardness settingSalt Indicator Light How to Fill the Salt ReservoirThe Salt Reservoir 1. Open theDecorated Items c a r i n g f o r y o u r d i n n e r w a r ePlastic AluminiumECO PROGRAM - when to use STANDARD PROGRAM - when to usew a s h p r o g r a m s HeavyWater Softener Setting Rinse Agent Settingoption adjustment mode section of the User Guide d i s h w a s h e r s t a n d a r d s t e s tHow to Adjust the Rinse Agent Setting HOW TO ENTER OPTION ADJUSTMENT MODEHow to Adjust the Water Softener Setting o p t i o n a d j u s t m e n t m o d eHow to Remove the End of Wash Program Beeps How to Remove the Auto Power Optiono p t i o n a d j u s t m e n t m o d e Prefinished ModelsHow to Install the Clean Dish Indicator How to Install the Closed Drawer Optiono p t i o n a d j u s t m e n t m o d e Prefinished Modelsu s e r m a i n t e n a n c e i n s t r u c t i o n s CLEANING THEIridium Finish Matt Stainless Steel Stainless Steel Finish Brushed StainlessCleaning the Filter Plate Cleaning the Drain Filter, Spray Arm and Filter PlateCleaning the Drain Filter Cleaning the Spray ArmProblem t r o u b l e s h o o t i n gPossible Causes What to Dooccurs on the first use or when the ProblemPossible Causes What to DoHow to Attend to a Fault How to Recognize a Fault Codef a u l t c o d e s F1 F2 F3 F4 F9 U1operating the InstallationInstallation and service must be performed by a qualified technician Do not install or store the where it will beOperational Maintenancewhilst the f i s h e r & p a y k e l m a n u f a c t u r e r ’ s w a r r a n t y This warranty DOES NOT coverFISHER & PAYKEL UNDERTAKES TO PRODUCT DETAILSc u s t o m e r c a r e Before you call for service or assistanceIn the USA if you need assistance Installation Checklist c h e c k l i s tUSA Customer Care - 1 888 9 FNP USA Copyright Reserved Fisher & Paykel