AUTOREPEAT RECORDING

Autorepeat Recording

The same tape can be recorded over many times.

œFollow the Before starting steps, under “NORMAL RECORDING”.

1Set the REPEAT REC switch to the “ON” position.

øThe REPEAT indicator will light.

2Press the MENU button until the (SET UP 3) menu is displayed.

øThe “ALARM MODE” setting is flashing.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@DURATION@@@20S

öVERTICAL@SYNC@@@@Y

öEXT@TIME@ADJ.@@@@01:00

öTAPE@IN@MODE@@@@@STOP

öTAPE@END@MODE@@@@R1 öTAPE@END@OUT@@@@@-3M öCLOG@DETECT.@@@@@Y öSERIES@REC@IN@@@@N öRS-232C@@@@@@@@@@19200

3Turn the JOG dial, until the “TAPE END MODE” setting is flashing.

4Turn the SHUTTLE ring to set to “R 1” or “R 2”. (See “Setting the Mode at the End of the Tape”)

5Press the SEARCH button to save the setting.

øThe setting procedure is now completed.

6Press the REC/PLAY SPEED l (or j) button to set the recording speed mode.

7Press the REC button.

øRecording will start. When the tape end is reached, the VCR will rewind it to the beginning, and recording will resume.

øWhen the end of the tape is reached, a buzzer will be heard (if in the (SETUP 2) menu, in the BUZZER section TAPE END is set to “Y”) and “OFF” will be displayed until the rewinding operation starts.

NOTES:

œIf during autorepeat recording there is an alarm trigger, “AL” is displayed on the digital display and alarm recording will take place. (Please refer to page 17, “ALARM RECORDING”.)

œIf the “TAPE END MODE” setting is R 1, the REPEAT indicator will go off if there is an alarm trigger. The recording will continue to the end of the tape then it will be rewound to the beginning and stop. “OFF” will be displayed on the digital display. To turn off the buzzer (if in the (SETUP 2) menu, in the BUZZER section TAPE END is set to “Y”) and the “OFF” display, press the STOP, EJECT or PLAY button, or turn the SHUTTLE ring.

œIf “AL” is displayed on the digital display and the “TAPE END MODE” setting is R1, autorepeat recording is not possible.

Setting the Mode at the End of the Tape

In the (SET UP 3) menu, you can set the mode of the VCR mode when the tape reaches the end during recording.

1Press the MENU button until the (SET UP 3) menu is displayed.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@DURATION@@@20S

öVERTICAL@SYNC@@@@Y

öEXT@TIME@ADJ.@@@@01:00

öTAPE@IN@MODE@@@@@STOP

öTAPE@END@MODE@@@@REW öTAPE@END@OUT@@@@@-3M öCLOG@DETECT.@@@@@Y öSERIES@REC@IN@@@@N öRS-232C@@@@@@@@@@19200

2Turn the JOG dial, until the “TAPE END MODE” setting is flashing.

3Turn the SHUTTLE ring, to set the desired mode.

œSetting when the REPEAT REC switch is set to the “OFF” position.

REW. . . . . . . Rewinds the tape to the beginning, then goes to stop mode

STOP . . . . . . Goes to stop mode EJECT . . . . . The cassette is ejected

œSetting when the REPEAT REC switch is set to the “ON” position.

R1. . . . . . . . . Autorepeat recording mode is automatically canceled if there was an alarm trigger

R2. . . . . . . . . Autorepeat recording mode is active even if there was an alarm trigger

4Press the SEARCH button to save the setting.

16

English