Flying Mole DADM310 owner manual Connections, Specifications, Dimensions Maintenance

4 Connections

■Connecting Devices

●Make sure the power of all related equipments is turned off, when wiring and checking their polarity.

●Make sure that the cable is not shorted, when connecting the speaker cable.

●Connect the power cable after all connections are complete.

Preamplifier, CD Player, etc.	Power Amplifier, etc.
(*1, 2)	(*3)

Connect to AC Outlet

(*1)

Speaker

	AC Power Cable
(* 1) Select an input with the selector on the rear panel of the	(* 2) XLR cables can be used to connect BALANCE outputs
amplifier.	of a CD player, preamplifier, etc. The signal arrangement
• FIXED (The LEVEL adjustment knob on the front panel	of the BALANCE INPUT on this product is:
is bypassed.)	1: GND, 2: HOT, and 3: COLD

•VARIABLE ( The level can be adjusted with the LEVEL

adjustment knob on the front panel.)	(* 3) When balance signals are input, the same signals as the
• BAL (The level can be adjusted with the LEVEL ad-
	input signals are output. The signal arrangement of the
justment knob on the front panel.)
	BALANCE OUTPUT on this product is:
	1: GND, 2: HOT, and 3: COLD

●Connection of the REMOTE POWER CONTROL Trigger

By connecting the REMOTE POWER CONTROL Trigger, the activation/deactivation of power on a Flying Mole power amplifier equipped with REMOTE POWER CONTROL Trigger Input can be interlocked with the activa- tion/deactivation of power on this device. Refer to the owner’s manuals of the devices to be connected as well before connecting cables.

1. Remove the attachment to the REMOTE POWER CONTROL connec-

tors.

2. Remove insulation material around the ends of the supplied remote con-

nection cables and twist the wires until they are stranded securely.

3. Insert the wires into the holes in the attachment and tighten the screws	Remote connection	+
	cable
to fix the cables. (Be sure to check polarity before connection)
		–

*Connect the other ends of the cables to the connector for the device whose power is to be interlocked as in the steps 1 to 3 above.

(The connector is also attached to the device to be connected.)

4. Connect the connectors to the REMOTE POWER CONTROL connec-	* Be sure to check polarity before
tors of the amplifier and of the other product.	connection.
• To control the power of the amplifier from the other product, connect the con-	Connect the black cable to the
nectors to the "IN" of this product and to the "OUT" of the other product.	negative terminal.

•To control the power of the other product from this product, connect the con- nectors to the "OUT" of the amplifier and to the "IN" of the other product.

*Commercially available vinyl insulated cables can be used as well. • Compatible cable type is AWG24 to AWG12. Refer to the steps 1 through 4 above when connecting cables and make sure that the polarity is correct.

5 Specifications

●This product should be placed close to the main source of electrical power (wall outlet in your house) and keep the power plug within reach.

●Connectors names may be different from this manual.

✱Refer to the owner’ s manuals of the equipments to be connected as well.

(* 4) BALANCE SIGNAL PARALLEL CONNECTION

Outputs from a preamplifier or a CD player can be input to more than one power amplifiers by connecting as shown below. Power can be interlocked by using REMOTE POWER CONTROL trigger connectors.

(Refer to the “u Connection of the REMOTE POWER CONTROL Trigger” section for information about REMOTE POWER CONTROL.)

Preamplifier, CD Player, etc.

●Connecting a Speaker Cable

qStrip the cover of the cable by about 10mm (3/8”). e Turn a speaker connector counterclockwise to loosen it.

w Twist the wires until they are stranded securely. r Insert the whole stranded wires of the cable and turn the

speaker connector clockwise to tighten it.

10mm

*Twist the wires of the speaker cable until they are stranded securely and take care not to leave any part of the stranded wires out of the speaker connector when connecting the speaker cable. If the wires come in contact with the rear panel or the wires at the positive terminal come in contact with the wires at the negative terminal, the protection circuit may be activated to stop the normal operation of the product.

Caution

●This product has DC amplifier circuit construction. (Sound signal goes through no capacitor from input to the speaker output.)

Therefore, a little noise may be heard when the power is turned on or off depending on the connected device.

Rated Output	300W / 4Ω, 100W / 8Ω
Total Harmonic Distortion	0.05% (@90W/8Ω / 1kHz)
Frequency Response	DC–20kHz (+0dB / –0.5dB) / 8Ω	DC–50kHz (+0dB / –3dB) / 8Ω
S/N Ratio	120dB (IHF-A, INput short-circuited)
Input Sensitivity	UNBAL : 1V / BAL : 2V
Input Impedance	FIXED : 100kΩ, VARIABLE : 47kΩ (BAL / UNBAL, Vol MAX)
Power Consumption	55W
Power Supply	AC 120V 60Hz (U.S.A.) / AC 230V 50Hz
Use Environment	0°C – 40°C
Dimensions inch / mm	8-7/16" (W) x 3-9/16" (H) x 15-15/16" (D) / 214 (W) x 91 (H) x 405 (D)
Weight	4.0 kg (8.8 lbs)

*Nameplate is on the bottom of the product.

*Due to product improvement, specifications and/or product design are subject to change without notice.

6 Dimensions

7 Maintenance

Never use liquids such as benzine, thinners, etc., chemically treated cloths, and do not spray any aerosol type insecticides on the amplifier. Clean the case using only a soft, dry cloth.

If the amplifier becomes soiled, mix a solution of water and a neutral detergent then dampen a soft cloth in the solution, wring out as much of the solution as possible, and clean the am- plifier. Then use a soft, dry cloth to wipe the surface dry.

Liquids

Benzine

Soft cloth

Neutral detergent

			24	(15/16”)
			(14-9/16”)		(15-15/16”)
			370		405
2	210 (8-1/4”)	2	11	(7/8”)
(1/16”)	214 (8-7/16”)	(1/16”)
			88	(3-7/16”)	91	(3-9/16”)
			3	(1/8”)		Unit: mm (”)

Privacy Policy

Security of Collected Information

We maintains strict physical, electronic, and administrative safeguards to protect your personal informatio n from unauthorize d or inappropriat e access. We restricts access to information about you to who need to know the information to respond to your inquiry or request. Who misuse personal information are subject to disciplinary action.

This document is printed with soy ink	FLYING MOLE CORPORATION
(an organic ink made from soy oil) on	5199-1 Waji-cho, Hamamatsu 431-1115 Japan.
recycled paper. Environmentally	Tel : +81-53-486-6030 Fax : +81-53-486-6033
friendly printed matter.	http://www.flyingmole.co.jp
		FP40697-000