3) Electrical Data
Electrical Data
| Model | V(E,H)A09K25V(E,H)A09K34V(E,H)09K50V(E,H)A12K25V(E,H)A12K34V(E,H,)A12K50V(E,H)A18K25V(E,H)A18K34V(E,H)A18K50 | ||||||||
| |||||||||
Voltage ( V) | 230/208 | 230/208 | 230/208 | 230/208 230/208 230/208 230/208 230/208 230/208 | |||||
LRA - Comp. (A) | 21 | 21 | 21 | 24.0 | 24.0 | 24.0 | 47 | 47 | 47 |
Cooling Current (A) | 4.4/4. 9 | 4.4/4. 9 | 4.4/4.9 | 5.5/6.1 | 5.5/6.1 | 5.5/6.1 | 9.2/10.2 | 9.2/10.2 | 9.2/10.2 |
MIN. Ckt. Amps (A) | 15 | 20 | 30 | 15 | 20 | 30 | 15 | 20 | 30 |
Power Connection | HARD WIRED | HARD WIRED | HARD WIRED | ||||||
Sample Nameplate (see your chassis nameplate)
FRIEDRICH AIR CONDITIONING CO. |
| WARNING | 120524 | |
MODEL NO 1 |
|
|
| LISTED |
SERIAL NO * |
|
|
|
|
SAN ANTONIO, TEXAS |
|
| HEATING AND | |
|
| |||
VOLTS: 24,33,34 |
|
| ELECTRICAL SHOCK AND | COOLING EQUIPMENT |
VOLTAGE RANGE: |
| |||
REFRIG CHARGE: 7 OZS. R22 |
|
| ||
| MOVING PARTS HAZARD | APPLICABLE PATENTS: | ||
DESIGN PRESSURE: 575 PSIG HS / 150 PSIG LS | ||||
COOLING: BTU/HR 8 |
| CAN CAUSE INJURY OR | US 6,065,296 | |
SEER: 10 | COP: 16 |
| NY MEA NO.: | |
HEAT PUMP BTU/HR: 14 |
| DEATH | ||
TOTAL COOLING AMPS: 9 |
| USE ONE OF THE | ||
TOTAL ELEC. HEAT AMPS: 15 |
| PULL OUT DISCONNECT | FOLLOWING ITEMS | |
ELECTRIC HEAT WATTS: 18 |
| FROM EACH CATEGORY | ||
FOR PERMANENTLY CONNECTED UNITS ONLY: | HE D LOCATED ON THE | TO COMPLETE THE | ||
COMP'. PLA 11 LRA 12 |
| FRONT OF THIS UNIT TO | ASSEMBLY | |
MOTOR: FLA 13 HP 19 |
| WALL PLENUM: | ||
HEATER AMPS: 17 |
| DIS BLE POWER BEFORE | ||
MIN. CKT AMP ~0 USE ~1 MAX. TIME DELAY FU | VPAWP1 | |||
|
|
| SERVICING. | VPAWP1 |
OR HACR TYPE CIRCUIT BREAKER. |
| SAMPLE | ||
GENERAL UNIT INFORMATION: |
| OUTDOOR GRILLE | ||
|
| VPAL2 | ||
MAX OUTLET AIR TEMPERATURE: 2OO'F |
| |||
| INDOOR GRILLE | |||
MAX EXTERNAL STATIC PRESSURE ELECTRIC |
| |||
HEAT'..5 IN. WATER |
|
| VPRG1 | |
"O" CLEARANCE TO COMBUSTIBLE MATERIAL |
| VPRG2 | ||
USE ON SINGLE OUTLET CIRCUIT ONLY |
| VPRG5 | ||
|
| |||
|
|
|
|
|
Important: all 208/230v chassis must be hard wired with properly sized breaker. See nameplate for specific chassis electrical requirements. See page 8 - Figure 5 for unit wiring and wall thermostat wiring. See page 8 for wire size. Use HACR type breakers to avoid nuisance trips. All field wiring must be done in accordance with nec and local codes.
7
