Avoid Service Checklist

Before you call for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

This oven is equipped with a state of the art electronic oven controller. Among its many features is a full time oven circuit diagnostics system. The controller constantly monitors its internal circuitry as well as several crucial oven circuits to insure they are all operating correctly. If at any time one of these systems fails, the controller will immediately stop operation, and beep continuously (flashing an error code of F1 or F3* in the display window, if equipped).

OCCURRENCE	POSSIBLE CAUSE/SOLUTION
Range is not level.	Poor installation. Place oven rack in center of oven. Place a level on the oven rack. Adjust
	leveling legs at base of range until the rack is level. When range is level, cooktop may
	appear out of alignment if countertop is not level.

	Weak, unstable floor. Be sure floor is level and can adequately support range. Contact
	a carpenter to correct sagging or sloping floor.

	Kitchen cabinet misalignment may make range appear to be unlevel. Be sure cabinets
	are square and have sufficient room for range clearance.

Cannot move appliance easily. Appliance	Cabinets not square or are built in too tight. Contact a cabinet maker to correct the
must be accessible for service.	problem.

	Contact builder or installer to make appliance accessible.

	Carpeting interferes with range. Provide sufficient space so range can be lifted over
	carpet.

	Gas line is hard-plumbed. Have a flexible A.G.A./C.G.A. approved metal appliance
	connector installed.

*Oven control beeps continuously with no	Electronic control has detected a fault condition. Turn the Temperature Control Knob
indicator lights flashing. (If model is	to OFF, and disconnect the power to the range. Wait 30 seconds and reconnect the
equipped with a display, F1 or F3 will	power. If fault recurs, disconnect the power and contact an authorized servicer.
show.)

Surface burners do not light.	Surface Control knob has not been completely turned to LITE. Push in and turn the
	Surface Control knob to LITE until burner ignites and then turn control knob to desired
	flame size.

	Burner ports are clogged. Clean burners. See "To Clean the Contoured Well Areas,
	Burner Cap Assembly, Trim Ring (some models), Burner Pan (some models) and Burner
	Base" under General Cleaning. With the burner off, clean ports with a small-gauge
	wire or needle.

	Range power cord is disconnected from outlet (Electric Ignition Models only). Be sure
	cord is securely plugged into the outlet.

	Electrical power outage (electric ignition models only). Burners can be lit manually. See
	Setting Surface Controls in this Owner's Guide.

Surface burner flame burns half way	Burner ports are clogged. With the burner off, clean ports by using a small-gauge wire
around.	or needle.

	Moisture is present after cleaning. Lightly fan the flame and allow burner to operate
	until flame is full. Dry the burners thoroughly following instructions in the General
	Cleaning section.

Surface burner flame is orange.

Dust particles in main line. Allow the burner to operate a few minutes until flame turns blue.

In coastal areas, a slightly orange flame is unavoidable due to salt air.

316000653 specifications

The Frigidaire 316000653 is a highly regarded replacement oven burner element that has become a popular choice for both homeowners and professionals. As part of Frigidaire's commitment to quality, this product showcases an impressive blend of performance, reliability, and advanced technology, making it a valuable addition to any kitchen.

One of the standout features of the 316000653 is its robust construction. Designed with high-quality materials, this burner element can withstand the rigors of daily cooking while providing consistent heat output. Its durable design ensures longevity, which makes it a smart investment for anyone looking to replace an older, malfunctioning burner.

The 316000653 offers powerful heating capabilities, boasting a quick response time that allows for greater cooking efficiency. Whether you're boiling water, sautéing vegetables, or simmering sauces, this burner can reach the desired temperatures rapidly, making it ideal for a variety of cooking techniques. The element cooks evenly, reducing hot spots and ensuring that every dish is prepared to perfection.

Installation of the 316000653 is straightforward, making it accessible for those who choose to handle repairs themselves. With its precise fit and compatibility with multiple Frigidaire models, users can rest assured that the element will seamlessly integrate into their existing setups. This ease of installation reduces downtime and allows for quicker cooking readiness.

In terms of safety, the Frigidaire 316000653 incorporates several design elements that prioritize user protection. It is built to minimize the risk of electrical hazards, ensuring that you can focus on your culinary endeavors with peace of mind. Additionally, the surface of the element is designed for easy cleaning, allowing for maintenance that keeps your kitchen looking pristine.

The versatility of the Frigidaire 316000653 makes it suitable for various cooking styles, from stovetop frying to baking and broiling. Its ability to deliver consistent performance across a wide range of dishes ensures that it meets the needs of both amateur cooks and seasoned chefs alike.

In summary, the Frigidaire 316000653 is a top-tier oven burner element that combines durability, efficiency, and safety. With its powerful heating capabilities, easy installation, and compatibility with numerous Frigidaire models, it stands out as an essential component for any kitchen. Whether you’re upgrading an old part or performing routine maintenance, the 316000653 promises to enhance your cooking experience.

Frigidaire 316000653 important safety instructions Avoid Service Checklist

Models: 316000653