Frymaster Series SR52, Series SR62 Connection to the Gas Supply Line, Propane Applications

SUPER RUNNER SERIES GAS FRYERS

CHAPTER 1: INSTALLATION INSTRUCTIONS

AUSTRALIAN REQUIREMENTS:

To be installed on a firm, level surface in accordance with AS 5601 / AG 601, local authority, gas, electricity, and any other relevant statutory regulations. The Australian orifice size and manifold pressures are listed below for the SR62.

Model	Gas Type	Orifice Size	Manifold Pressure KPa
SR62	Nat	2.53 mm	0.9 KPa
SR62	Prop	1.6 mm	2.4 KPa

CE UNITS ONLY:

Manifold Pressure Inches WC 3.6” 9.6”

Nominal Heat Inputs (Qn), Gas Type, Orifice Size, Pressures and Adjustments, Orifice Quantity/Color, Burner Markings and Pilot Markings are listed in the table below:

	NOMINAL		ORIFICE	MANIFOLD GAS PRESSURE		ORIFICE	BURNER	PILOT
MODEL*	HEAT INPUT-	GAS TYPE
	Qn		SIZE (MM)	MBAR	INCH W.C.	QTY/ COLOR	MARKING	MARKING
	(kW)
		G20	2.40	12,0	4,8	5/BLUE	Blue	26N
SR62 GM	37.5	G25	2.40	17,5	7,0	5/BLUE	Blue	26N
		G31	1.51	22,0	8,8	5/RED	Red	16LP
SR52 GM	30	G20	2.40	12,0	4,8	4/BLUE	Blue	26N
		G25	2.40	17,5	7,0	4/BLUE	Blue	26N
		G31	1.51	22,0	8,8	4/RED	Red	16LP
		G20	2.40	12,0	4,8	3/BLUE	Blue	26N
SR42 GM	26	G25	2.40	17,5	7,0	3/BLUE	Blue	26N
		G31	1.51	22,0	8,8	3/RED	Red	16LP

*SR prefix- Super Runner Series

*GM suffix- gas millivolt system with no electrical supply connections required

NON-CE UNITS ONLY:

Nominal Heat Inputs (Qn), Gas Type, Orifice Size, Pressures and Adjustments, Orifice Quantity, and Pilot Markings are listed in the table below:

	NOMINAL			MANIFOLD GAS
	HEAT INPUT-		ORIFICE		ORIFICE	PILOT
MODEL*		GAS TYPE		PRESSURE
	Qn		SIZE (MM)	(INCH W.C.)	QUANTITY	MARKING
	(BTU)
SR62 GM	150	NAT	2.53(#39)	4	5	26N
		LP	1.51(#53)	11	5	16LP
SR52 GM	120	NAT	2.53(#39)	4	4	26N
		LP	1.51(#53)	11	4	16LP
SR42 GM	105	NAT	2.80(#35)	4	3	26N
		LP	1.70(#51)	11	3	16LP

*SR prefix- Super Runner Series

*GM suffix- gas millivolt system with no electrical supply connections required

NOTE: Outlet gas pressure must be adjusted strictly within the above requirements 5 to 10 minutes after the appliance is operating.

1.4Connection to the Gas Supply Line

NOTE: The gas supply (service) line must be the same size or greater than the fryer inlet line. This appliance is equipped with a ½-inch (15-

mm)inlet. The gas supply line must be sized to accommodate all gas- fired equipment connected to the line. Consult the local gas company or supplier, or your local contractor for minimum supply line requirements.

NOTE: If quick-disconnect supply lines or flex lines are used, increase supply line size to ¾-inch (22-mm) or larger.

Propane Applications;

Proper Regulator Must Be Installed

1-3