Model: BUF-06E
Range Hood
INSTALLATION MANUAL
SAFETY INSTRUCTIONS
NAMES OF PARTS | CIRCUIT DIAGRAM |
Before installation and operation, read these instructions carefully and use this product only in the manner described by the manufacturer in the operation manual.
The instruction shown below are used to alert you to potential personal injury and property damage hazards.
There are three hazard classifications based on potentially dangerous situations.
Obey all safety instructions that show these symbols to avoid possible injury, death and property damage.
WARNING: WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
4.TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a)Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including
b)Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), and The American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
c)When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d)Ducted fans must always be vented to the outdoors.
e)The end user is responsible to ensure compliance with all Federal, State and Local Environmental and Fire codes.
5. TO REDUCE THE RISK OF FIRE, USE ONLY |
METAL DUCTWORK. |
ConnectorLamp:50W
ON | OFF | Lamp | Front Cover |
|
|
|
(Not supplied) |
| Black | Black | |||
|
| |||||
|
|
|
|
|
| |
|
|
| Enclosure |
| White | White |
Lamp Switch |
| Switch (Lamp) |
|
|
| |
|
|
|
|
|
| |
Lamp |
|
|
|
| Terminal |
|
|
|
| Black | Connector | Lamp:50W | |
|
|
|
| |||
(Not supplied) |
|
|
|
| ||
|
| 120V 60Hz |
|
|
| |
|
|
|
| Black | Black | |
|
|
|
|
| ||
|
|
| Green | White |
|
|
|
|
| White Black |
| White | White |
|
|
|
| Black |
|
|
|
|
|
| White |
|
|
|
|
| Connector | Connector | Terminal |
|
|
|
|
|
| ||
Filter
SIZE & DIMENSIONS | ACCESSORIES |
NOTE: The safety instructions are explained with the following pictographic symbols.
means prohibition. It indicates actions, if any, that mustn’t be done.
means forcible execution. It indicates actions, if any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
b)Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
2. To reduce the risk of fire or electric shock, do not |
use this product with any |
device. |
3. Do not attempt to control Remote Blower using |
the internal switch provided on the front panel of |
the |
THIS SWITCH IS TO BE USED FOR THE |
CONTROL OF THE LIGHTS ONLY! A SEPARATE |
S W I T C H , W I T H P R O P E R LY R AT E D |
AMPERAGE MUST BE INSTALLED TO |
CONTROL THE REMOTE BLOWER MOTOR. |
6. | This unit must be grounded. |
7. | Install this range hood to a liner. Check that the |
| hood is correctly installed, since incorrect |
| installation could result in the range hood becoming |
| detached and falling off. |
8. | Connect only to an AC120 Volt power source or |
| the range hood could result in fire, electric shock, |
| and damage. |
CAUTION
1. | For general ventilating use only. Do not use to |
| exhaust hazardous or explosive material and |
| vapors. |
2. | To reduce the risk of fire and to properly exhaust |
| air, be sure to duct air outside. Do not vent exhaust |
| air into spaces within walls or ceilings or into attics, |
| crawl spaces, or garages. |
3. | Read specification label on this product for further |
| information and requirements. |
4. | Use only for the purpose of kitchen ventilation. |
5. Do not install this range hood in the bathroom or in | |
| other wet rooms since electrical shock and damage |
| may result. |
6. | Fasten the filter and other parts securely. Incorrect |
| attachment may result in personal injury or property |
| damage. |
7. Keep your hands and other objects away from the | |
| fan while it is in motion. The range hood may injure |
| you or damage itself. |
8. | To reduce the risk of fire and electric shock, install |
Ø7/8"
9/16" | |
| 3- |
26"
9/16"
27"
(Unit: inch)
|
| |
Holes for mounting range hood | Screw M5⋅30 | Nut with plate |
| ||
| Four (4) pieces | Four (4) pieces |
9/16" |
| |
RANGE HOOD LOCATION | ||
|
| |
1 The range hood must be in- |
| |
|
| |
| stalled just above the cooktop. |
|
| 1" |
|
| 2 The minimum distance from the |
|
| cooking surface to the bottom |
|
| of the range hood must be 24". | Liner |
|
| |
24" (Minimum)
3 The total weight of the | Cook top |
range hood unit is 11 lbs. (5 kg) |
|
4 Power requirements are: AC120 V, 60 Hz, 1.0 Amp
WARNING:
•Check that the hood is correctly installed, since incorrect installation could result in the detachment of the range hood and the unit could fall.
CAUTION:
Contact the Remote Blower manufacturer or a |
Certified Electrician for their recommendations. |
this range hood only with remote blower models |
rated maximum current of 12.8 amps. |
•To protect hands from injury, wear working gloves when installing the range hood.
INSTALLATION
WARNING:
• If the range hood is not installed properly, it could become detached and fall.
• Ensure that the metal duct does not touch other metal housing materials, otherwise fire or electric shock could result.
CAUTION:
•Wear working gloves to avoid injury.
•To prevent air or moisture from entering through the wall opening, be sure to install wall insulation to seal around duct work completely.
1Detach the filters by loosening 2 screws. Then remove 5 screws fixing the front cover and detach the front cover.
Screw
WARNING:
•Electrical wiring should be done by a qualified person(s) in accordance with all applicable codes and standards, including
•This range hood uses 120V AC. Do not connect to other voltage since fire, electric shock or damage could result.
1)Remove the switch’s protective cardboard.
WARNING:
Remove the protective cardboard without fail, otherwise there is a risk of fire.
Cardboard
1 According to the conditions where the range hood is installed, de- | |||
termine whether it will be discharged vertically or horizontally (10" | |||
Round duct). For vertical or horizontal discharge, run duct work be- | |||
transitions and elbows. As for installing the exterior blower, please | |
referto itsinstallation. | |
tween the hood location and the exterior blower used with the range hood. For best result in either direction, use a minimum number of
Filter
Front cover
Loosen 2 screws
to remove the filter. Cardboard
1 Remove the nut from the conduit connector at the end of power wiring.
WARNING:
Be sure to switch power OFF at service panel before wiring.
2 Remove two
Conduit (Not supplied)
Nut
(Not supplied)
Front cover
Screw
CAUTION:
(Do not remove yet.)
screws fixing the wire cover and detach it.
Do not remove the switch’s protective cardboard until proceeding to “4. Final Assembly and Check”.
2 Hold up the range hood and align the 4 screw holes of the liner and range hood, then fix securely using the supplied screws (M5⋅30) and nuts.
Note: Fasten all the screws and nuts evenly.Wire cover
Screw
Filter
2) | Attach the front cover, and secure it with 5 screws. |
| Then attach the filters. |
3) | Two 50 Watt halogen light bulbs (not supplied) can be mounted |
Liner
3 Connect the conduit through the connecting hole of the body using the nut previously removed.
Conduit
Nut
in this range hood. |
Prior to function check, install light bulbs (PAR20 bulb, with |
base diameter 26 mm: medium base), rated 120 V - 50 Watt or |
below. |
The following light bulbs are recommended for this range hood. |
• GE Model No. 50PAR20H/FL25 |
• SYLVANIA Model No. 50PAR20/HAL/DL/NFL |
Turn the lamps
Bulb |
(Not supplied) |
| 2 Check |
(1) Turn on the electrical circuit |
to the range hood. |
2 The range hood unit must be mounted to a liner which has the following dimensions. Install the liner securely after checking that the opening size of the liner is the same as the figure below.
Liner Dimensions!!"#$ |
| |
| ||
| ||
|
| |
CAUTION:
•The liner shape illustrated in this installation manual is only for reference.
CAUTION:
•When the liner is installed in the wooden hood, the inside of the wooden hood placed above the cooking surface must be fully covered by the metal barrier including bottom edges. Select a suitable liner and metal barrier according to the size and shape of the wooden hood and install properly.
•The liner should be installed tightly. If the liner installation is not correct, the range hood unit may become detached and fall.
| ||
Securing plate | [Right & left, each | |
two (2) places] | ||
|
[Securing plate turns while passing through the opening of Liner]
Liner
Four screws (M5⋅30)
3 Check that the top of the ex- haust port is inserted into the bottom of 10" round duct, then make the duct joint secure and air tight using
4
5
Connect the electrical wires as follows:
•Black to Black•White to White
•Green to Green
Connect wires tightly and securely using wire connectors (not supplied).
Replace the wire cover with the screws removed previously. Make sure that all wires are connected properly and enclosed inside of the wiring compartment.
Wire cover
Screw
Wire Connector (Not supplied)
(2) | Make sure that the switch |
|
| and light operate correctly. |
|
| Refer to page 5 of the |
|
| Operation Manual. |
|
(3) | Make sure that the range |
|
| hood functions rightly and it | Push to turn ON |
|
|
has no abnormal noises and/or vibration.
*As for operating the exterior blower used with this hood, please refer to its operation manual.
5.Explanation to the End User(1)Referring to the Operation Manual, explain the operation of this range hood to end users.
(2)The Installation Manual and Operation Manual should be given to the end user.
