Manuals / Fujitsu / Computer Equipment / Network Router

Fujitsu AP-600RP-USB manual System Status

Models: AP-600RP-USB

1 63

Download 63 pages 30.26 Kb

Page 24

CONNECT2AIR™ WLAN AP-600RP-USB

Page 23 / 62

8.2System Status

This section shows the AP’s working status:

•

•

•

•

•

AccessPoint properties

The wireless network name is displayed.

Wide Area Network (WAN)

The status of the WAN port will be displayed as well as the connection type.

Local Area Network (LAN)

The IP address, DHCP server and the firewall status are displayed

Wireless Settings (WLAN)

If enhanced security has been set, it will be displayed. The Access Control displays the status of the WLAN access possibilities – for example, WEP, 802.1x or Radius.

Printer Status

Possible values for the printer status include “Ready”, “Not ready”, and “Printing…”.

Image 24

Fujitsu AP-600RP-USB manual System Status

Contents

Page AP-600RP-USB Technical SupportFCC Information Federal Communications Commission FCC StatementCE Declaration of Conformity FCC RF Radiation Exposure StatementContent Wlan OverviewAppendix a Licensing Information Introduction Five steps to successPrepare your PCs and devices to connect to the AccessPoint Install and configure the AccessPointInstall additional features for example, a printer server Determine your network knowledgeFunctions and Features Included in deliveryWireless Network Fundamentals Ad-hoc Mode Peer-to-Peer WorkgroupWlan Overview Ieee StandardsService Set Identification Ssid Infrastructure ModeHardware Installation LED indicatorsReset switch Front PanelProcedure for Hardware Installation Network Settings Network BasicsClient Network Settings Network SettingsConfiguration of your Wireless Client Check the Connection Configuration Examples Connecting the devices to the AP-600RP-USB Installation NoteAP-600RP-USB with Adsl Router AP-600RP-USB with Adsl Router advanced AP-600RP-USBAP-600RP-USB with Adsl Modem AP-600RP-USB with Cable Modem Two AP-600RP-USB in repetition mode WDS AP-600RP-USB FloorSoftware Installation Install AP Start-up ToolAccesspoint Configuration Start-up and LogSystem Status How to connect to your Internet Service Provider ISP WizardStatic IP Address Dynamic IP Address PPP over Ethernet e.g. Adsl connectionPptp L2TP Without an ISPWireless Settings Country / Region Wireless network ID SsidTurbo mode / NitroTM mode Band modulation typeWired Equivalent Privacy WEP Security WEP keys 1, 2, 3Primary Setup IP Pool Starting / Ending Address NetmaskLease Time minutes Client ListDNS Settings Address ReservationWAN Type Configuration / Connection to the Internet ISP Wireless Settings Country / Region Authentication Wlan SecurityEncryption Wireless Security Settings Security begins when Changing the Standard PasswordWired Equivalent Privacy WEP Settings ApplicationWi-Fi Protected Access WPA WPA Enterprise ModeWPA for Soho applications Ieee 802.1x and Radius ServerRadius Server Access Control List General access modeUser-specific access list Example configuration of a publicly accessible WEBcamParametrization of the Ddns client in the AccessPoint Ddns Dynamic DNSRelease of the route in the virtual server Tips for configuring a WDS 16 WDSExample Static IP address Advanced Settings Virtual ServerApplication Firewall Increased firewall protection by closing the portsFirewall configuration Add Firewall RuleCONNECT2AIR Wlan AP-600RP-USB Example of a firewall configuration RequirementsPC 2 in the Internet 192.35.35.10 with destination AP-600RP CONNECT2AIR Wlan AP-600RP-USB Time Zone 4 DMZAdministrator Toolbox Firmware UpgradeToolbox Access to USB Printers Through Wlan Configuration on Windows 2000/XP PlatformsCONNECT2AIR Wlan AP-600RP-USB Troubleshooting Press FinishAppendix a Licensing Information Availability of source codeCONNECT2AIR Wlan AP-600RP-USB CONNECT2AIR Wlan AP-600RP-USB CONNECT2AIR Wlan AP-600RP-USB No Warranty END of Terms and Conditions