Manuals / Brands / Computer Equipment / Scanner / Fujitsu / Computer Equipment / Scanner

Fujitsu FI-4120C2 ■ Connecting the SCSI Interface Cable, • SCSI card:, • SCSI interface cable:, the Fujitsu web site (FAQ), SCSI Device Connector is used

1 28

Download 28 pages, 1.32 Mb

2.Connect the other end of the USB interface cable to the PC.

•Be sure to use the USB cable which

ATTENTION

comes as an accessory with this scanner.

Correct operation with commercially available cables is not guaranteed.

• When connecting to an USB hub,

use the first stage USB hub that is

closest to the computer. If you use

the second or later hub stages, the

scanner may not operate correctly.

• This scanner is provided with two

interfaces: Ultra SCSI and USB 2.0 /

1.1. On this scanner, each of the

SCSI and USB interface is con-

trolled not to be used simulta-

1.Insert the SCSI interface cable into the interface connector until both sides click.

2.Connect the other end of the cable to the per- sonal computer.

neously. Scanner can be only

connected to either USB or SCSI

interface.

■ Connecting the SCSI Interface Cable

When using the scanner with a SCSI interface, a commercially available SCSI interface cable and SCSI card must be purchased.

• SCSI interface cable:

Use a connector which complies with Ultra

SCSI. A 50 Pin Contact Shielded High-Density

SCSI Device Connector is used.

ATTENTION

HINT

Be careful not to bend the pins of the SCSI cable when connecting to the scanner .

The factory default setting for SCSI ID is "ID 5". If the SCSI ID of another SCSI device is set to the same ID, either change the scanner's SCSI ID or SCSI ID of the other SCSI device. Set the device address using the SCSI ID switch on the back of the image scan- ner.

• SCSI card:

Find the recommended SCSI card information in

the Fujitsu web site (FAQ).

http://imagescanner.fujitsu.com/

•When connecting the SCSI interface

ATTENTION

cable, turn the scanner off. Be sure to first connect the SCSI interface cable and, then turn on the power of the scanner and the personal com- puter.

•In a SCSI daisy chain formation, connect the scanner so that it is the terminated device.

ATTENTION

	4	5	6
	3		7
Click	2		8
	2
	1	0	9
		0

This scanner supports two interfaces: Ultra SCSI and USB 2.0/1.1.

On this scanner, each of the SCSI and USB interface can not to be used simultaneously. Scanner can only connect to the USB or SCSI interface.

fi-4120C2 Image Scanner Getting Started		4

Contents

P3PC-E917-02EN Page Chapter 1 PREPARING THE SCANNER Chapter2 INSTALLATION OF THE SCANNER Appendix TROUBLESHOOTING INTRODUCTION ■Regulatory Information Their standards and logos ( ) are uniform among participating nations Use in High-safetyApplications About the Use of Mercury To avoid unexpected injury, read the following carefully Doing the following actions may result in serious personal injuries: ■Note, Liability ■Safety Precautions Do not use the scanner if you smell a strange odor Do not install the scanner on unstable surfaces Do not block the ventilation ports Do not place heavy objects or climb on top of the scanner Firmly insert the power plug Do not install the scanner in direct sunlight Be aware of the pick spring Chapter 1 PREPARING THE SCANNER 1.1Checking the Contents of the Scanner Package 1.2Names and Functions of Parts 1.3 Operator Panel Chapter2 INSTALLATION OF THE SCANNER 2.1 Installing the Scanner 2.2Connecting the Scanner to Your PC ■ Connecting the SCSI Interface Cable 2.3Installing the Scanner Application For FUJITSU TWAIN32 Scanner Driver 5. Click [INSTALL PRODUCTS] 6. Click [TWAIN Driver] on the window below 7. Error Recovery Guide Installation window appears 9.Follow the instructions on the window to install the application Installation of the scanner driver is completed 3. Click [ScandAll 21] on the window below ■Installing ScandAll 1.Insert the Setup CD-ROMinto the CD drive 2.Click [INSTALL PRODUCTS] For FUJITSU ISIS Scanner Driver ■Installing the FUJITSU ISIS Scanner Driver 1.Press the power button to turn ON the scanner 2.Turn your PC on and log on to Windows 6. Click [ISIS Driver] on the window below 7.Error Recovery Guide Installation window appears ■Installing QuickScan Pro™ 1.Insert the Setup CD-ROMinto a CD drive 3.Click [QuickScan PRO (Trial)] on the window below Now the installation of the scanner driver is completed 4.Continue to install the application following the instructions on the window 5.Enter the required information, then click [Next >] button From the [Start] menu, select [Programs]-[Quick- Scan]-[QuickScan] 3.Select [Select Scanner...] from [Scan] menu in QuickScan Pro™ 5.Select [Preview Scan] from the [Scan] menu. And then the document is scanned Error Recovery Guide Image Processing Software Option (Trial) Adobe® Acrobat® 1.Insert the Adobe Acrobat 6.0 CD-ROMinto your CD-ROMdrive 3.Click the [Next] button when the following screen is displayed Installation will start and the setup screen will appear Appendix 1 TROUBLESHOOTING AP-1 AP-2 AP-3 Appendix 2 DAILY CARE ■Cleaning Materialse Cleaning Parts Remarks Appendix 3 REPLACING CONSUMABLES AP-5 P3PC-E917-02EN