3. Connector for thermal head drive (CN7)
Part number |
| : | |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
No. |
|
|
| Signal | I/O | Contents | No. |
|
| Signal | I/O | Contents | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
|
| BAT | — | Power for head | 2 |
| BAT | — | Power for head | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
| GND | — | Head ground | 4 |
| GND | — | Head ground | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
5 |
|
| HD2 | O | Print data output | 6 |
| LAT | O | Printing data latch | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
|
| HDV | O | Power for logic | 8 |
| HCLK | O | Printing transmitting clock | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
9 |
|
| ENB8 *1, 2 | O | Printing enable (not used) | 10 |
| ENB7 *1,2 | — | Printing enable (not used) | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
11 |
| ENB6 | O | Printing enable | 12 |
| ENB5 | O | Printing enable | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13 |
|
| VREF | O | Power for thermistor | 14 |
| TMP | O | Temperature detection | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
15 |
|
|
|
| *3 | — | Connected with No. 17 | 16 |
| HDV | O | Power for logic | |||||||
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
17 |
|
|
|
| *3 | — | Connected with No. 15 | 18 |
|
|
|
|
|
| *4 | — | Head rank specify (not used) | ||
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| *4 |
|
|
|
|
|
|
|
|
| |||||
19 |
|
|
|
| — | Not used | 20 |
| ENB4 | O | Printing enable | ||||||||
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
21 |
| ENB3 | O | Automatic paper loading | 22 |
| ENB2 | O | Printing enable | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
23 |
| ENB1 | O | Printing enable | 24 |
| GND | — | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
25 |
| GND | — | Printing enable | 26 |
| BAT | — | Power for head | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Notes:
*1: Mechanism selection signal and the printing enable signal for 3” mechanism.
*2: Not used at the combination with 2” mechanism.
*3: At the mechanism side, this pin number is for the printing data 2.
Since this pin number is used for the printing data 1 at the interface board, the No. 15 and No. 17 pins are connected.
*4: This signal is used for the adjustment of printing duty depending upon the rank of thermal head resistor. Not used at this interface board.
•Symbol
•“I” or “O” means a signal direction from the interface board side.
4.Connector for abnormal head temperature detection (CN6)
Part number |
| : | ||||||
Mating connector part number : | ||||||||
|
|
|
|
|
|
|
|
|
No. | Signal |
| I/O | Contents | No. | Signal | I/O | Contents |
|
|
|
|
|
|
|
|
|
1 | TMPER |
| O | Abnormal head temperature detection | 2 | N.C. | — | Not connected |
|
|
|
|
|
|
|
|
|
3 | GND |
| — | Logic ground |
|
|
|
|
|
|
|
|
|
|
|
|
|
Note: This signal detects abnormal head temperature.
9