Furuno GP-1850DF installation manual

INSTALLATION MANUALCOLOR DGPS/PLOTTER/SOUNDERGP-1850DFCOLOR GPS/PLOTTER/SOUNDERGP-1850F

Safety Instructions for the Installer .......................i

Equipment Lists .....................................................ii

System Configuration ...........................................iv

1. Installation of Standard Equipment ...............1-1

1.1 Installation of Display Unit ..............................................1-1

1.2 Installation of Antenna Unit .............................................1-3

1.3 Installation of Transducers ...............................................1-4

1.4 Installation of Sensors ....................................................1-14

2. Wiring ...............................................................2-1

3. Initial Settings ..................................................3-1

3.1 NMEA Setting ..................................................................3-1

3.2 Output Data Sentences .....................................................3-3

3.3 Antenna Height................................................................. 3-4

3.4 Baud Rate Setting (GP-1850DF only).............................. 3-4

3.5 Beacon frequency Setting (GP-1850DF only) .................3-5

3.6 Depth Adjustment............................................................. 3-6

3.7 External Equipment Setup (Option) .................................3-7

3.8 Selecting the Echo Sounder Output Power ....................3-10

4. Installation of DGPS Beacon Receiver

(for GP-1850F) .................................................4-1

APPENDIX TRIDUCER 525ST-PWC/PWD .......AP-1

PACKING LIST ....................................................A-1

OUTLINE DRAWINGS......................................... D-1

INTERCONNECTION DIAGRAM ........................ S-1

SCHEMATIC DIAGRAM...................................... S-2

Contents

Main INSTALLATION MANUAL COLOR DGPS/PLOTTER/SOUNDER GP-1850DF COLOR GPS/PLOTTER/SOUNDER GP-1850F PUB. No. IME-43950-J FIRST EDITION : FEB. 1999 J : NOV. 01, 2001 iiiiiiiiiiiii CAUTION CAUTION SAFETY INSTRUCTIONS Safety Instructions for the Installer ii Equipment Lists Standard supply Optional equipment iii Optional equipment (con't) iv System Configuration *Required for 1 kW transducer only 1-1 1. Installation of Standard Equipment 1.1 Installation of Display Unit Mounting considerations Figure 1-1 Tabletop, overhead mounting methods 1-2 Mounting procedure Note: Tabletop, overhead mounting Figure 1-2 Tabletop, overhead mounting of display unit Flush mounting 1.2 Installation of Antenna Unit Mounting considerations Clamp nut Connector shell Gasket (reddish brown) Washer Shield 1-4 1.3 Installation of Transducers Figure 1-5 Inside-hull transducer mounting location Installing the inside-hull mount transducer Necessary tools Remarks on installation 1-5 Attaching the transducer Figure 1-7 Attaching transducer to hull with silicone sealant Figure 1-6 Coating the transducer face with silicone sealant 1-6 1-7 5 32.8 DGPS 3D 50kHz 10 15 0.0 Installing the thru-hull mount transducer Figure 1-11 Transducer outline drawings Transducer mounting location Transducer outline drawings 1-9 Acceptable transducer mounting locations Typical through-hull mount transducer installations 1-10 Procedure for installing the thru-hull mount transducer Figure 1-15 Construction of fairing block 1-11 Installing the transom mount transducer Figure 1-16 Transom mount transducer mounting locations Installing the transom mount transducer flush with hull (for flat hulls) 1-12 Figure 1-17 Transom mount transducer, mounting flush with hull Transducer preparation 1-13 Triducer 524ST-MSD, 525ST-MSD Mounting considerations 1.4 Installation of Sensors Page 1-16 Through-hull mount water temperature/speed sensor ST-02MSB, ST-02PSB Figure 1-22 Water temperature/speed sensor ST-02MSB, ST-02PSB 2-1 2. Wiring Figure 2-2 Connecting the power cable to the battery Transducer All wiring are terminated at the rear of the display unit. Antenna unit CAUTION Note: Transducer Water temperature/speed sensor Ground Extending antenna cable length Figure 2-4 Waterproofing connector Figure 2-3 Cable extension 2-4 How to attach the N-P-8DFB connector Figure 2-5 Fabrication of coaxial cable 3-1 3. Initial Setting 3.1 NMEA Setting NMEA port 3-2 DGPS port 3-3 3.2 Output Data Sentences Figure 3-3 Output Date Sentences Display Input/Output Sentences 3-4 3.3 Antenna Height ANT. HEIGHT 0 0 5 m 3.4 Baud Rate Setting (GP-1850DF only) 3-5 3.5 Beacon Frequency Setting (GP-1850DF only) 3-6 3.6 Depth Adjustment DEPTH ADJ + 0.0 f t 3-7 3.7 External Equipment Setup (Option) Speed Source 3-8 Speed Adjustment Temperature Adjustment 3-9 3-10 3.8 Selecting the Echo Sounder Output Power 3-11 Figure 3-15 Removing cover assembly Figure 3-16 ANLG Board WARNING Do not connect the power cable with the cover removed. 5. Move the jumper block on JP1 from 3-4 to 1-2 on the ANLG Board. Page 4-1 4. Installation of DGPS Beacon Receiver (for GP-1850F) GR-802-1650-10N-019 GR-802-1650-15N-019S 4-2 Disassembly WARNING 4-3 Installation of DGPS receiver Procedure 4-4 4-5 4-6 Figure 4-8 Attaching chassis assembly 11.Reassemble the display unit. Figure 4-9 Remounting the cover Note : 4-7 Checking the DGPS installation AP-1 APPENDIX TRIDUCER 525ST-PWC/PWD INSTALLATION INSTRUCTIONS Transom Mount Transducer or TRIDUCER Multisensor with Integral Release Bracket AP-2 P66 Installation template AA A BB B Step 1 Step 4Step 3Step 2 latch AP-3 Attaching the Sensor to the Bracket Cable Routing Page Page Page Page 4-8 Connecting DGPS beacon receiver Figure 4-11 Connecting DGPS beacon receiver