Safety Instructions

Operating Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING —

SAVE THESE INSTRUCTIONS

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, and to prevent property damage, personal injury, or death.

WARNING! WATER HEATER SAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all hot water faucets and allow them to run for several minutes. Do this before using any electrical appliance which is connected to the hot water system. This simple procedure will allow any built- up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our website at www.ge.com. In Canada visit www.geappliances.ca.

Troubleshooting Tips

■Connect to a grounded metal, permanent wiring system; or run an equipment-grounding conductor with the circuit conductors and connect to the equipment-grounding terminal or lead of the appliance.

■Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.

■Dispose of discarded appliances and shipping or packing material properly.

■Do not attempt to repair or replace any part of your dishwasher unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

■To minimize the possibility of electric shock, disconnect this appliance from the power supply before attempting any maintenance.

NOTE: Turning the dishwasher off does not disconnect the appliance from the power supply. We recommend having a qualified technician service your appliance.

CAUTION: To prevent minor injury or property damage

Consumer Support

■Contents washed in Anti-bacterial mode, if

available, may be hot to the touch. Use care before handling.

 

■Using a detergent that is

 

not specifically designed

 

for dishwashers will cause

 

the dishwasher to fill with

 

suds.

 

■If your dishwasher is connected to a

 

wall switch, ensure that the switch is

 

on prior to use.

 

■On dishwashers with electronic controls,

 

if you choose to turn the wall switch

 

off between wash cycles, allow 5-10

 

seconds after turning the switch on before

2

touching START/RESET to allow the control

to boot.

 

■Non-Dishware Items: Do not wash items such as electronic air cleaner filters, furnace filters and paint brushes in your dishwasher. Damage to dishwasher and discoloration or staining of dishwasher may result.

■Close supervision is necessary if this appliance is used by or near children.

■Load light, plastic items so they will not become dislodged and drop to the bottom of the dishwasher—they might come into contact with the heating element and be damaged.

Page 1 Page 3
Page 2
Image 2
GE 165D4700P382 Operating Instructions, Troubleshooting Tips, Consumer Support, On dishwashers with electronic controls
Page 1 Page 3

165D4700P382 specifications

The GE 165D4700P382 is a highly regarded component within the realm of industrial and commercial applications, known for its robustness and reliability. This device serves as a vital part of various electrical systems, providing efficient performance and superior operation in challenging environments.

One of the main features of the GE 165D4700P382 is its advanced protection capabilities. It is designed to safeguard equipment from overloads, short circuits, and voltage spikes, thereby prolonging the life of connected machinery and reducing the likelihood of failures. This protective functionality is essential in environments where electrical disturbances can lead to significant downtime and costly repairs.

The GE 165D4700P382 incorporates cutting-edge technology that enhances its efficiency and versatility. This component is equipped with state-of-the-art microprocessor-based controls that allow for precise monitoring and management of the electrical system. These controls enable functionalities such as adjustable trip settings, remote monitoring, and integration into automated systems, making it an adaptable choice for contemporary industrial settings.

Another key characteristic of the GE 165D4700P382 is its robust construction. Built to withstand extreme temperatures and harsh environmental conditions, this component is rated for high performance even in the most demanding applications. Its housing is designed to resist dust, moisture, and other contaminants, ensuring reliable operation without the need for frequent maintenance.

The device's compact design facilitates easy integration into existing electrical systems, making installation straightforward and efficient. Furthermore, the GE 165D4700P382 offers various mounting options, allowing for flexibility in deployment depending on the specific requirements of the application.

In summary, the GE 165D4700P382 stands out due to its advanced protection features, high-performance microprocessor technology, robust construction, and user-friendly design. These characteristics make it an indispensable asset in industrial and commercial settings, ensuring optimal performance and reliability in electrical systems. As industries continue to evolve with increasing demands for efficiency and safety, the GE 165D4700P382 remains a trusted choice for professionals seeking quality and innovation in their electrical components.
Top Page Image Contents