SafetyInstructions

Preparing to install the refrigerator.

Read these instructions completely and carefully.

Water Supply to the Icemaker (on some models)

If the refrigerator has an icemaker, it will have to be connected to a cold water line.

Refrigerator Location

A water supply kit (containing copper tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer or from Parts and Accessories, 800-626-2002.

Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

Clearances

Install it on a floor strong enough to support it fully loaded.

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections:

Sides 5/8″ (15 mm) Top 1″ (25 mm)

If built-in, allow 7/8 (22 mm) for hinge covers.

Back 1″ (25 mm)

If the refrigerator is against a wall on either side, allow the following door clearances:

20′, 22′, and 25′ models

3/4″ (19 mm)

27′ models

11/2″ (38 mm)

TroubleshootingTips Installation Instructions OperatingInstructions

CustomerService

Rollers

The rollers have 3 purposes:

1 Rollers adjust so the door closes easily when opened about halfway. [Raise the front about 5/8″ (15 mm) from the floor.]

To assure that the doors will close automatically from a halfway open position, there is a built-in tilt from the front to the back of the cabinet. Side-by- side refrigerators also have specially designed door hinges that lift both doors slightly when opened, allowing the force of gravity to help close them securely.

2 Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble.

3 Rollers allow you to move the refrigerator away from the wall for cleaning.

14

To adjust the rollers, remove the base grille by pulling it out at the bottom.

Turn the roller adjusting screws clockwise to raise the refrigerator, counterclockwise to lower it. Use an adjustable wrench (3/8″ hex head bolt) or pliers.

To replace base grille, align prongs on back of grille with clamps in cabinet and push forward until grille snaps into place.

Page 14
Image 14
GE 20-27 owner manual Preparing to install the refrigerator, Refrigerator Location, Clearances, SafetyInstructions, Rollers

20-27 specifications

The GE 20-27 is a groundbreaking innovation in the realm of gas turbine technology, designed to meet the increasing energy demands with unparalleled efficiency and sustainability. This turbine model exemplifies the commitment of General Electric to deliver power solutions that not only drive economic growth but also align with environmental stewardship.

One of the main features of the GE 20-27 is its high efficiency in power generation. The turbine operates within a combined-cycle power plant environment, integrating both gas and steam turbines to maximize energy output from the same fuel input. This method significantly raises the overall efficiency, often exceeding 60%, which is a benchmark in modern power generation.

Technologically, the GE 20-27 employs advanced materials and components that enhance its durability and performance. The turbine blades are made from high-strength alloys and ceramic matrix composites, designed to withstand extreme temperatures and stresses. This focus on materials science not only improves the longevity of the turbine but also enhances its performance, allowing it to operate under a wide range of conditions.

The turbine incorporates cutting-edge aerodynamic design principles to increase airflow and optimize combustion efficiency. With its innovative combustion system, the GE 20-27 achieves lower emissions, contributing to cleaner power production. This aspect is particularly vital in a world increasingly concerned with climate change and pollution. The reduced nitrogen oxides (NOx) and carbon emissions make the GE 20-27 a viable option for utilities looking to enhance their environmental profile.

Additionally, the GE 20-27 features advanced digital capabilities through GE's Digital Wind Farm initiatives. This integration allows operators to monitor performance in real-time, utilizing data analytics to predict maintenance needs and optimize operational efficiency. The predictive maintenance capability transforms the way operators manage power generation, leading to reduced downtime and increased reliability.

Another characteristic worth noting is the flexibility of the GE 20-27 to run on various fuels, including natural gas and renewable sources. This versatility allows operators to adapt to changing market conditions and regulatory environments without significant investments in new infrastructure.

In conclusion, the GE 20-27 turbine model showcases a harmonious blend of efficiency, technology, and environmental responsibility. Through advanced design and materials, coupled with digital innovation, it stands as a hallmark of modern energy solutions, capable of addressing both the present and future needs of the global energy landscape.