Installing the water line.

Read these instructions completely and carefully.

Before You Begin

When connecting a GE Reverse Osmosis Water System to your refrigerator, the only approved installation is with a GE RVKIT.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter, use the refrigerator’s filter bypass plug. Using the refrigerator’s water filtration cartridge in conjunction with the RO filter can result in hollow ice cubes and slower water flow from the water dispenser.

This water line installation is not warranted by the refrigerator or icemaker manufacturer.

Follow these instructions carefully to minimize the risk of expensive water damage.

Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the water line to the hot water line.

If you use your refrigerator before connecting the water line, make sure the icemaker feeler arm is kept in the STOP (up) position.

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a power drill) during installation, be sure the device is insulated or wired in a manner to prevent the hazard of electric shock.

All installations must be in accordance with local plumbing code requirements.

What You Will Need

To determine how much copper tubing you need:

Measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Then add 8 feet (244 cm). Be sure there is sufficient extra tubing [about 8 feet (244 cm) coiled into 3 turns of about 10 inches (25 cm) diameter] to allow the refrigerator to move out from the wall after installation.

A water supply kit (containing copper tubing, shutoff valve and fittings listed below) is available at extra cost from your dealer or from Parts and Accessories, 800-626-2002.

Cold water supply. The water pressure must be between 20 and 120 p.s.i. (1.4–8.2 bar) on models without a water filter and between 40 and 120 p.s.i. (2.8–8.2 bar) on models with a water filter.

Power drill.

Copper tubing, 1/4″ outer diameter to connect the refrigerator to the water supply. Be sure both ends of the tubing are cut square.

Do not use plastic tubing or plastic fittings because the water supply line is under pressure at all times. Certain types of plastic tubing may become brittle with age and crack, resulting in water leakage.

Two 1/4outer diameter compression nuts and 2 ferrules (sleeves)—to connect the copper tubing to the shutoff valve and the refrigerator water valve.

If your existing water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting.

Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32″ at the point of connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type

15

valve complies with your local plumbing codes.

Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips

Customer Service

Page 15
Image 15
GE 20-27 owner manual Installing the water line, Before You Begin, What You Will Need, Power drill

20-27 specifications

The GE 20-27 is a groundbreaking innovation in the realm of gas turbine technology, designed to meet the increasing energy demands with unparalleled efficiency and sustainability. This turbine model exemplifies the commitment of General Electric to deliver power solutions that not only drive economic growth but also align with environmental stewardship.

One of the main features of the GE 20-27 is its high efficiency in power generation. The turbine operates within a combined-cycle power plant environment, integrating both gas and steam turbines to maximize energy output from the same fuel input. This method significantly raises the overall efficiency, often exceeding 60%, which is a benchmark in modern power generation.

Technologically, the GE 20-27 employs advanced materials and components that enhance its durability and performance. The turbine blades are made from high-strength alloys and ceramic matrix composites, designed to withstand extreme temperatures and stresses. This focus on materials science not only improves the longevity of the turbine but also enhances its performance, allowing it to operate under a wide range of conditions.

The turbine incorporates cutting-edge aerodynamic design principles to increase airflow and optimize combustion efficiency. With its innovative combustion system, the GE 20-27 achieves lower emissions, contributing to cleaner power production. This aspect is particularly vital in a world increasingly concerned with climate change and pollution. The reduced nitrogen oxides (NOx) and carbon emissions make the GE 20-27 a viable option for utilities looking to enhance their environmental profile.

Additionally, the GE 20-27 features advanced digital capabilities through GE's Digital Wind Farm initiatives. This integration allows operators to monitor performance in real-time, utilizing data analytics to predict maintenance needs and optimize operational efficiency. The predictive maintenance capability transforms the way operators manage power generation, leading to reduced downtime and increased reliability.

Another characteristic worth noting is the flexibility of the GE 20-27 to run on various fuels, including natural gas and renewable sources. This versatility allows operators to adapt to changing market conditions and regulatory environments without significant investments in new infrastructure.

In conclusion, the GE 20-27 turbine model showcases a harmonious blend of efficiency, technology, and environmental responsibility. Through advanced design and materials, coupled with digital innovation, it stands as a hallmark of modern energy solutions, capable of addressing both the present and future needs of the global energy landscape.