Water Temperature Setting

DANGER: There is a hot water scald potential

if the thermostat is set too high. Households with small children, disabled, or elderly persons may require a 120°F or lower thermostat setting to prevent contact with HOT water.

The temperature of the water in the water heater can be regulated by setting the temperature dial of the adjustable surface mounted thermostat(s) located behind the jacket access panel(s).

Dual element heaters have two thermostats.

Safety and energy conservation are factors to be considered when selecting the water temperature setting of the water heater’s thermostat(s). The lower the temperature setting, the greater the savings in energy and operating costs.

To comply with safety regulations the thermostat(s) are factory set at 120°F or less where local codes require. This is the recommended starting point.

Water temperatures above 125°F

can cause severe burns or death from scalding. Be sure to read and follow the warnings outlined in this manual and on the label on the water heater. This label is located on the water heater near the thermostat access panel.

Mixing valves are available for reducing point of use water temperature by mixing hot and cold water in branch water lines. Contact a licensed plumber or the local plumbing authority for further information.

The chart below may be used as a guide in determining the proper water temperature for your home.

Safety Instructions Installation Instructions Operating Instructions

Time/Temperature Relationship in Scalds

Temperature	Time To Produce a Serious Burn
120°F	More than 5 minutes
125°F	11/2 to 2 minutes
130°F	About 30 seconds
135°F	About 10 seconds
140°F	Less than 5 seconds
145°F	Less than 3 seconds
150°F	About 11/2 seconds
155°F	About 1 second

Table courtesy of Shriners Burn Institute

Care and Cleaning

Reset button	T	R
	E	E
	S		S
	E		S
	R	T	E
	R	T
Thermostat
dial pointer
	150°F		90°F
	125°F
	TURN OFF
Thermostat	POWER
	BEFORE
	SERVICING
protective
cover

Type 59T thermostat and protective cover.

If adjustment is necessary…

Turn off the power to the water heater.

Remove the jacket access panel(s) and insulation exposing the thermostat(s).

The thermostat protective cover(s) should not be removed.

Using a small screwdriver, set the thermostat(s) dial pointer(s) to the desired temperature.

Replace the insulation and jacket access panel(s). Turn on the power to the water heater.

Troubleshooting Tips Customer Service

GE30T06MAG, AP12170-4 specifications

The GE AP12170-4, also known as the GE30T06MAG, is a cutting-edge product designed to enhance efficiency and reliability in various industrial applications. This model has garnered attention due to its advanced features, robust technologies, and overall performance characteristics.

One of the standout features of the GE AP12170-4 is its high power capacity, which enables it to handle demanding loads in large industrial environments. The device is engineered to maintain continuous operation even under extreme conditions, making it ideal for critical infrastructures where downtime is not an option. Its durable construction is designed to withstand harsh environmental factors, ensuring longevity and consistent performance.

In terms of technology, the GE AP12170-4 integrates state-of-the-art control systems that facilitate precise monitoring and management of electrical loads. This technology allows users to optimize energy consumption while simultaneously safeguarding against overloads. The built-in diagnostics and data logging capabilities provide real-time insights into operational efficiency and can be crucial for predictive maintenance, reducing unexpected failures and operational costs.

Additionally, this model features advanced safety mechanisms, including surge protection and fault detection systems, which are essential for minimizing risks associated with electrical surges and other anomalies. This focus on safety extends to user-friendly interfaces, which simplify the operation and maintenance of the device. Operators can easily navigate through settings and troubleshoot potential issues, enhancing overall usability.

The GE AP12170-4 also incorporates flexible connectivity options, allowing it to integrate seamlessly into existing systems. Whether using legacy communication protocols or modern networks, users can enjoy versatile connectivity that enhances interoperability with other industrial equipment. This adaptability is vital for facilities undergoing digital transformation and seeking to improve operational efficiency.

Moreover, the design of the GE AP12170-4 emphasizes energy efficiency, contributing to lower operational costs and reduced environmental impact. By optimizing performance and reducing energy waste, it aligns with the growing demand for sustainable practices in industrial operations.

Overall, the GE AP12170-4, or GE30T06MAG, represents a blend of power, reliability, and advanced technology. Its comprehensive features equip industries to meet the challenges of modern operations while prioritizing safety, efficiency, and sustainability. Whether in manufacturing, utility, or larger infrastructure projects, this model stands out as a versatile solution for meeting the demands of today’s industrial landscape.

GE AP12170-4, GE30T06MAG Water Temperature Setting, Time/Temperature Relationship in Scalds

Models: GE30T06MAG AP12170-4