Installation Instructions.

Cold Water Supply Fitting (cont.)

B.OPTIONAL HOME INSTALLATION

(Where codes permit)—Saddle Valve: Saddle valve must be able to connect with 1/4-inch tubing supplied with system.

Not supplied with product; check your local hardware or home service store for product

Saddle valve typically requires 1/2″OD tubing or larger.

NOTE: Codes in the state of Massachusetts require installation by a licensed plumber and do not permit the use of the saddle valve. For installation, use plumbing code 248-CMR of the Commonwealth of Massachusetts.

1.Turn off the cold water supply and install saddle valve as required by product selection. (Be sure to follow manufacturers’ installation instructions.)

DANGER: If hole is required to be drilled in pipe, to protect yourself from serious injury or fatal shock, use a battery powered hand drill only to make the hole. DO NOT USE AN ELECTRIC DRILL.

2.Open saddle valve only after complete system has been installed.

C.OPTIONAL INSTALLATION

(For installation with rigid pipe between supply valve and sink faucet)

Option 1

1.Remove pipe from supply valve and sink faucet.

2.Obtain flexible pipe sized to your plumbing.

3.Install flexible pipe.

4.Go back to A. Preferred Installation section step 3.

Option 2

1.Obtain compression fittings to fit rigid pipe.

2.Obtain any other fittings required to connect compression fittings to feed water adapter.

3.Remove pipe from supply valve.

4.Cut pipe to fit length of assembled fittings and adapter.

5.Install compression fitting to pipe.

6.Go back to A. Preferred Installation section step 3.

NOTE: Above described materials are not included with the product.

Faucet Spout Installations (see Fig. 2, page 8)

1.Remove spout (A) and faucet body (B) from faucet packaging.

2.Move the threaded dome-shaped collar (C) on the spout up and away from the o-rings on the spout.

3.Gently insert the spout into the top of the faucet body.

NOTE: Turning the spout left to right during installation will help the o-rings to slide in easily.

4.Once the spout (A) has been installed and fully seated, slide the threaded collar (C) down to the faucet body (B).

5.Tighten the collar by hand to the faucet body by turning in a clockwise direction.

Instrucciones de instalación.

Accesorio para el Suministro de Agua Fría (cont.)

B.INSTALACIÓN OPCIONAL EN EL HOGAR

(Donde lo permitan los códigos)—Válvula de asiento: La válvula de asiento debe poder conectarse con el tubo de 1/4 de pulgada suministrado con el sistema.

No se suministra con el producto; consulte en la ferretería local o tienda de servicios para el hogar.

La válvula de asiento típicamente requiere una tubería con un diámetro exterior de 1/2” o superior.

NOTA: Los códigos del estado de Massachusetts exigen la instalación por parte de un plomero con licencia y no permite el uso de una válvula de asiento. Para la instalación, utilice el código de plomería 248-CMR del estado de Massachusetts.

1.Cierre el suministro del agua fría e instale la válvula de asiento según lo requiera el producto (Cerciórese de seguir las instrucciones de instalación del fabricante).

PELIGRO: Si se necesita taladrar un agujero en la tubería, para protegerse contra lesiones serias o choques fatales, utilice únicamente un taladro manual operado por batería para perforar el orificio. NO UTILICE UN TALADRO ELÉCTRICO.

2.Abra la válvula de asiento unicamente después de haber instalado todo el sistema.

C.INSTALACIÓN OPCIONAL

(Para la instalación con una tubería rígida entre la válvula de suministro y el grifo del lavaplatos)

Opción 1

1.Remueva la tubería de la válvula de suministro y del grifo del lavaplatos.

2.Obtenga tubería flexible con un tamaño acorde con su tubería de la casa.

3.Instale la tubería flexible.

4.Refiérase a A. Sección de instalación preferida en el paso 3.

Opción 2

1.Obtenga accesorios de compresión para hacer el ajuste de la tubería rígida.

2.Obtenga cualquier accesorio requerido para conectar el adaptador de compresión al adaptador para la alimentación de agua.

3.Remueva la tubería de la válvula de suministro.

4.Corte la tubería para que se ajuste a la longitud de los accesorios ensamblados y al adaptador.

5.Instale el accesorio de compresión a la tubería.

6.Refiérase a A. Sección de instalación preferida en el paso 3.

NOTA: Los materiales descritos anteriormente no están incluidos con el producto.

Instalación del pico del grifo (ver Fig. 2, página 8)

1.Retire el pico (A) y pieza del grifo (B) del paquete del grifo.

2.Mueva el collar enroscado en forma de cúpula (C) en el pico hacia arriba y lejos de los aros tóricos en el pico.

3.Suavemente inserte el pico en la parte superior de la pieza del grifo.

NOTA: Girar el pico de la izquierda a la derecha durante la instalación ayudará a que los aros tóricos se deslicen fácilmente.

4. Una vez que el pico (A) se haya instalado y esté completamente acomodado, deslice el collar enroscado (C) hacia abajo en dirección de la pieza del grifo (B).

5. Apriete el collar a mano a la pieza del grifo girando en la dirección

del reloj.

7

Page 6 Page 8
Page 7
Image 7
GE GX1S50F Faucet Spout Installations see, Instalación del pico del grifo ver , página, Option, Opción
Page 6 Page 8

GX1S50F specifications

The GE GX1S50F is an advanced water filtration system designed to provide clean and safe drinking water for households. This innovative system utilizes cutting-edge technologies to ensure that contaminants are effectively reduced while enhancing the overall taste and quality of the water.

One of the main features of the GE GX1S50F is its three-stage filtration process. The system first employs a sediment filter that captures large particles such as dirt, sand, and rust, ensuring that these impurities do not reach the subsequent stages. Following this, a carbon block filter takes over, which is adept at removing chlorine, lead, and other harmful chemicals that can affect the water's taste and safety. Finally, the system features a post-carbon filter that polishes the water, providing the finishing touch to ensure that every drop is crystal clear and fresh.

The GE GX1S50F is designed with user convenience in mind. Its compact size makes it easy to install, fitting seamlessly under most sinks without taking up excessive space. The system is also equipped with a simple shut-off valve, which allows users to quickly halt water flow during filter changes, minimizing mess and ensuring a straightforward replacement process.

Another significant characteristic of the GE GX1S50F is its durability and longevity. The filters are engineered to last up to six months, depending on usage and water quality, allowing households to enjoy cleaner water for a prolonged period without frequent replacements. This not only saves time but also adds to the system's cost-effectiveness.

In addition to its performance features, the GE GX1S50F is designed with sustainability in mind. By providing an efficient means of filtering tap water, the system reduces the reliance on single-use plastic water bottles, promoting an eco-friendly approach to water consumption.

Overall, the GE GX1S50F is a state-of-the-art water filtration solution that combines advanced technology with practical design. With its three-stage filtration process, easy installation, long-lasting filters, and commitment to sustainability, it offers an excellent choice for families looking to improve their drinking water quality while being mindful of their environmental impact.
Top Page Image Contents