Manuals / GE / Household Appliance / Water System

GE GX1S50F installation instructions Mounting System Installation, Montaje del sistema

Models: GX1S50F

1 16
Download 16 pages 31.17 Kb
Page 9
Image 9

Installation Instructions.

Mounting System Installation

Pick a location under the sink to mount the system. Location should be easily accessible with at least 5 inches of clearance between the bottom of the filter canister and the floor or bottom of the cabinet; any less will result in difficulty of removing filter canister. Allow enough space on either side of the system for the tubing connections.

A. PREFERRED INSTALLATION

(Mounting Using the Screw Provided [Fig. 4])

1.Remove shrink wrap from filter system.

2.System should be mounted to a stud in the wall or solid firm surface.

3.Use the screw (B) provided to mount through the screw hole in the center of the manifold (A). (Pre-drill a 1/16″ pilot hole, if needed). NOTE: If mounting to drywall, with no stud, a drywall anchor (not included) must be used.

(B) Screw

(A) Manifold

Fig. 4

B. OPTIONAL INSTALLATION

(Mounting Using the Mounting Tape Provided [Fig. 5])

(If mounting to drywall, the screw must be used also).

1.Remove shrink wrap from filter system.

2.Clean wall surface to remove any dirt, oil or grease and dry thoroughly.

3.Using the double-sided mounting tape provided (C), remove one side of the protective wax paper and apply the entire piece to the back side of the manifold (A), applying firm pressure to the entire piece.

4.Remove the remaining wax paper from the double-sided mounting tape (C) and adhere it to the cleaned wall surface, applying firm pressure to the entire piece.

(A) Manifold

(C) Mounting tape

Fig. 5

Instrucciones de instalación.

Montaje del sistema

Seleccione una ubicación debajo del lavaplatos para instalar el sistema. La ubicación debe ser de fácil acceso, al menos con 5 pulgadas de espacio entre la base del cartucho del filtro y el piso o la base del gabinete; cualquier espacio inferior presentará dificultades para retirar el cartucho del filtro. Permita suficiente espacio para cualquier lado del sistema para las conexiones de la tubería.

A. INSTALACIÓN PREFERIDA

(Montaje utilizando el tornillo suministrado [Fig. 4])

1.Retire la envoltura del sistema del filtro.

2.El sistema debe estar instalado en una tachuela en la pared o superficie sólida.

3.Utilice el tornillo (B) suministrado para instalar a través del orificio del

tornillo en el centro del recolector (A). (Preperfore un orificio piloto de 1/16″, de ser necesario).

NOTA: Si se instala en pared de yeso, sin tachuela, se debe usar un ancla de pared de yeso (no incluida).

(B) Tornillo

(A) Recolector

Fig. 4

B. INSTALACIÓN OPCIONAL

(Montaje utilizando la cinta de montaje suministrada [Fig. 5])

(Si la instalación es en una pared de yeso [drywall], también se debe usar el tornillo).

1.Retire la envoltura del sistema del filtro.

2.Limpie la superficie de la pared para retirar cualquier suciedad, aceite o grasa y seque completamente.

3.Con la cinta de doble adhesivo para montaje que se suministra (C), retire un lado del papel cera protector y aplique a toda la pieza en la parte posterior del recolector (A), haciendo presión firme a toda la pieza.

4.Retire el papel cera restante de la cinta de doble adhesivo (C) y péguela a la superficie limpia de la pared, aplicando presión firme a toda

la pieza.

(A) Recolector

(C) Cinta para montaje

Fig. 5

9

Page 8 Page 10
Page 9
Image 9
GE GX1S50F Mounting System Installation, Montaje del sistema, Mounting Using the Screw Provided Fig
Page 8 Page 10

GX1S50F specifications

The GE GX1S50F is an advanced water filtration system designed to provide clean and safe drinking water for households. This innovative system utilizes cutting-edge technologies to ensure that contaminants are effectively reduced while enhancing the overall taste and quality of the water.

One of the main features of the GE GX1S50F is its three-stage filtration process. The system first employs a sediment filter that captures large particles such as dirt, sand, and rust, ensuring that these impurities do not reach the subsequent stages. Following this, a carbon block filter takes over, which is adept at removing chlorine, lead, and other harmful chemicals that can affect the water's taste and safety. Finally, the system features a post-carbon filter that polishes the water, providing the finishing touch to ensure that every drop is crystal clear and fresh.

The GE GX1S50F is designed with user convenience in mind. Its compact size makes it easy to install, fitting seamlessly under most sinks without taking up excessive space. The system is also equipped with a simple shut-off valve, which allows users to quickly halt water flow during filter changes, minimizing mess and ensuring a straightforward replacement process.

Another significant characteristic of the GE GX1S50F is its durability and longevity. The filters are engineered to last up to six months, depending on usage and water quality, allowing households to enjoy cleaner water for a prolonged period without frequent replacements. This not only saves time but also adds to the system's cost-effectiveness.

In addition to its performance features, the GE GX1S50F is designed with sustainability in mind. By providing an efficient means of filtering tap water, the system reduces the reliance on single-use plastic water bottles, promoting an eco-friendly approach to water consumption.

Overall, the GE GX1S50F is a state-of-the-art water filtration solution that combines advanced technology with practical design. With its three-stage filtration process, easy installation, long-lasting filters, and commitment to sustainability, it offers an excellent choice for families looking to improve their drinking water quality while being mindful of their environmental impact.