Installation Instructions.

Faucet Installation

Be sure there is room underneath and above the sink to make the needed connections. Before starting, make sure there is sufficient room for the battery powered faucet base. Select one of the following places to install the faucet:

1.In an existing sink spray attachment or soap dispenser hole.

2.In a hole to be drilled in the sink top.

3.In a hole to be drilled in the countertop, next to the sink.

NOTE: Be sure the faucet base will fit flat against the surface at the selected location so the bottom gasket between the base and surface area will seal.

Installation Steps (refer to Fig. 2 for clarification)

1.If drilling is needed, make a 3/4″ diameter hole.

Be sure to use the proper procedure for drilling porcelain or stainless steel. Special drill bits may be needed. Consult a qualified plumber for the proper procedure.

2.Remove the faucet with pre-installed tubing, thin o-ring (D), faucet base (E), bottom base gasket (F), lock washer (G), hex nut (H) and mounting bracket (I) from the packaging.

3.Feed tubing connected to the faucet through the thin o-ring (D), faucet base (E), bottom base gasket (F), lock washer (G) and hex nut (H).

4.Thread the hex nut (H) up the stem of the faucet until the height between the bottom of the base gasket (F) and top of the lock washer

(G) is slightly larger than the thickness of the mounting surface (J).

5.Lower the faucet assembly into place in the mounting hole and orient to final position. Place the mounting bracket (I) above the lock washer (G) around the faucet stem (Fig. 3). While holding the mounting bracket in place, securely tighten the hex nut.

NOTE: Two people may be required to complete this step.

Instrucciones de instalación.

Instalación del grifo

Cerciórese de que haya suficiente espacio debajo y encima del lavaplatos para realizar la conexión necesaria. Antes de empezar, cerciórese de que haya suficiente espacio para la base del grifo operada por batería. Seleccione uno de los siguientes lugares para instalar el grifo:

1.En un orificio accesorio rociador existente en el lavaplatos u orificio de dispensador de jabón.

2.En un orificio a perforar en la parte superior del lavaplatos.

3.En un orificio a perforar en el mostrador, al lado del lavaplatos.

NOTA: Cerciórese de que la base del grifo quede plana contra la superficie en la ubicación seleccionada de manera que el empaque de abajo entre la base y el área de la superficie quede sellado.

Pasos para la instalación (consulte la Fig. 2 para aclaración)

1.Si es necesario perforar, haga un orificio de 3/4″ de diámetro.

Cerciórese de utilizar el procedimiento correcto para perforar porcelana o acero inoxidable. Podría necesitar brocas adicionales. Consulte a un plomero calificado para el procedimiento correcto.

2.Retire del paquete el grifo con la tubería preinstalada, aro tórico fino (D), base del grifo (E), empaque inferior de la base (F), arandela de seguridad (G), tuerca hexagonal (H) y soporte de montaje (I).

3.Inserte la tubería conectada al grifo a través del aro tórico fino (D), la base del grifo (E), el empaque inferior de la base (F), la arandela de seguridad (G) y la tuerca hexagonal (H).

4.Enrosque la tuerca hexagonal (H) en el vástago del grifo hasta que la altura entre la parte inferior del empaque de la base (F) y la parte superior de la arandela de seguridad (G) sea ligeramente más grande que el grosor de la superficie de montaje (J).

5.Baje la ensambladura del grifo a su lugar en el orificio de montaje y oriente hacia la posición final. Coloque el soporte de montaje (I) por encima de la arandela de seguridad (G), alrededor del vástago del grifo (Fig. 3). Mientras sostiene el soporte de montaje en su lugar, apriete firmemente la tuerca hexagonal.

NOTA: Es posible que sean necesarias dos personas para completar este paso.

(A) Spout / Pico

(C) Collar / Collar

(B) Faucet body / Pieza del grifo

 

(D) O-ring / Aro tórico

 

(E) Faucet base / Base del grifo

(G) Lock washer /

Fig. 3

Arandela de seguridad

(F) Gasket / Empaque

(H) Hex nut /

 

Tuerca hexagonal

(J) Mounting surface /

 

(I) Mounting

Superficie de montaje

 

bracket /

Fig. 2

Soporte de

montaje

 

8

Page 7 Page 9
Page 8
Image 8
GE GX1S50F Faucet Installation, Instalación del grifo, Installation Steps refer to for clarification
Page 7 Page 9

GX1S50F specifications

The GE GX1S50F is an advanced water filtration system designed to provide clean and safe drinking water for households. This innovative system utilizes cutting-edge technologies to ensure that contaminants are effectively reduced while enhancing the overall taste and quality of the water.

One of the main features of the GE GX1S50F is its three-stage filtration process. The system first employs a sediment filter that captures large particles such as dirt, sand, and rust, ensuring that these impurities do not reach the subsequent stages. Following this, a carbon block filter takes over, which is adept at removing chlorine, lead, and other harmful chemicals that can affect the water's taste and safety. Finally, the system features a post-carbon filter that polishes the water, providing the finishing touch to ensure that every drop is crystal clear and fresh.

The GE GX1S50F is designed with user convenience in mind. Its compact size makes it easy to install, fitting seamlessly under most sinks without taking up excessive space. The system is also equipped with a simple shut-off valve, which allows users to quickly halt water flow during filter changes, minimizing mess and ensuring a straightforward replacement process.

Another significant characteristic of the GE GX1S50F is its durability and longevity. The filters are engineered to last up to six months, depending on usage and water quality, allowing households to enjoy cleaner water for a prolonged period without frequent replacements. This not only saves time but also adds to the system's cost-effectiveness.

In addition to its performance features, the GE GX1S50F is designed with sustainability in mind. By providing an efficient means of filtering tap water, the system reduces the reliance on single-use plastic water bottles, promoting an eco-friendly approach to water consumption.

Overall, the GE GX1S50F is a state-of-the-art water filtration solution that combines advanced technology with practical design. With its three-stage filtration process, easy installation, long-lasting filters, and commitment to sustainability, it offers an excellent choice for families looking to improve their drinking water quality while being mindful of their environmental impact.
Top Page Image Contents