Instructions

Care and cleaning of the oven.

Operating Instructions Safety

The gasket is designed with a gap at the bottom to allow for proper air circulation.

Do not rub or clean the door gasket— it has an extremely low resistance to abrasion.

If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

Cleaning the Oven Door

To clean the inside of the door:

Because the area inside the gasket is cleaned during the self-clean cycle, you do not need to clean this by hand.

The area outside the gasket and the door liner can be cleaned with a soap-filled steel-wool or plastic pad, hot water and detergent. Rinse well with a vinegar and water solution.

To clean the outside of the door:

Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse well. You may also use a glass cleaner to clean the glass

on the outside of the door. Do not let water drip into the vent openings.

If any stain on the door vent trim is persistent, use a soft abrasive cleaner and a sponge-scrubber for best results.

Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse.

Do not use oven cleaners, cleaning powders or harsh abrasives on the outside of the door.

Troubleshooting Tips Care and Cleaning

Slot

Hinge lock

Pull hinge locks down to unlock.

Removal position

Lift-Off Oven Door

The door is very heavy. Be careful when removing and lifting the door.

Do not lift the door by the handle.

To remove the door:

Fully open the door.

Pull the hinge locks down toward the door frame, to the unlocked position. A tool, such as a small flat-blade screwdriver, may be required.

Firmly grasp both sides of the door at the top.

Close door to the door removal position, which is halfway between the broil stop position and fully closed.

Lift door up and out until the hinge arm is clear of the slot.

To replace the door:

Firmly grasp both sides of the door at the top.

With the

Bottom

Hinge arm

door at the

edge

 

same angle as

of slot

 

the removal

 

 

position, seat the

 

indentation of

 

Indentation

the hinge arm

 

 

 

into the bottom

 

edge of the hinge

 

slot. The notch in the hinge arm

must be fully seated into the bottom

of the slot.

 

 

Fully open the door. If the door will not fully open, the indentation is not seated correctly in the bottom edge of the slot.

Push the hinge locks up against the front frame of the oven cavity, to the locked position.

Hinge arm

Hinge lock

Push hinge locks up to lock.

Close the oven door.

Consumer Support

Removable Oven Floor

 

To remove the oven floor:

Clean the oven floor with warm

 

Remove the oven door using the

soapy water.

 

 

 

instructions in the Lift-Off Oven Door

When reinstalling the oven floor, be

 

section of this manual.

sure to slide it all the way to the back

 

Press down and pull out the

of the oven.

Press down and pull out.

IMPORTANT: Always replace the

removable oven floor.

24

 

removable floor before the next use.

Page 24
Image 24
GE JCK 915, JCT 915 Operating Instructions Safety, Troubleshooting Tips Care and Cleaning, Cleaning the Oven Door

JCT 915, JCK 915 specifications

The GE JCK 915 and JCT 915 are advanced electric locomotives that exemplify modern engineering and operational efficiency. These models are specifically designed to meet the demands of contemporary rail transport, offering reliability, performance, and reduced environmental impact.

One of the main features of the JCK 915 and JCT 915 locomotives is their powerful traction system. These models are equipped with high-efficiency traction motors that provide excellent acceleration and speed capabilities. This is particularly beneficial for freight services where the movement of heavy loads over long distances is required. The locomotives can operate effectively on various rail gauges, making them versatile for different rail networks.

The locomotives utilize cutting-edge technologies, including advanced diagnostic systems. These systems monitor the health and performance of critical components in real-time, allowing for proactive maintenance and reducing downtime. The integration of onboard data analytics ensures that operators can make informed decisions based on performance metrics, leading to increased efficiency and longevity of the locomotive.

The aerodynamic design of the JCK 915 and JCT 915 also contributes to their operational efficiency. With reduced drag coefficients, these locomotives can achieve higher speeds while consuming less energy. This design consideration aligns with the industry's growing emphasis on sustainability and lowering greenhouse gas emissions.

Safety is a top priority in the design of these locomotives. They come equipped with modern safety features, including advanced braking systems and collision avoidance technologies. The cab design provides improved visibility for the operators, enhancing overall safety during operations.

In terms of comfort, the cab area of the JCK 915 and JCT 915 is designed with the operator in mind. Ergonomic seating, modern controls, and climate control systems create a comfortable working environment, which can significantly enhance operational efficiency.

Moreover, both models are equipped with regenerative braking capabilities. This feature allows the locomotives to recover energy during braking, which can be reintegrated into the system, improving overall energy efficiency.

In summary, the GE JCK 915 and JCT 915 locomotives showcase a blend of power, efficiency, modern safety, and operator comfort. With their advanced features and technologies, they are well-suited to meet the evolving challenges of the rail industry, paving the way for a more efficient and sustainable future in transportation.