Using the clock and timer.

Not all features are on all models.

Make sure the clock is set to the correct time of day.

To Set the Clock

The clock must be set to the correct time of day for the automatic oven timing functions to work properly. The time of day cannot be changed during a delayed cooking or a delayed self-cleaning cycle.

Touch the TIMER/CLOCK pad twice.

Touch the + or – pad.

If the + or – pad is not touched within one minute after you touch the TIMER/CLOCK pad, the display reverts to

the original setting. If this happens, touch the TIMER/CLOCK pad twice and reenter the time of day.

Touch the START pad until the time of day shows in the display. This enters the time and starts the clock.

To check the time of day when the display is showing other information, simply touch the CLOCK pad. The time of day shows until another pad is touched.

To Turn Off the Clock Display

If you have several clocks in your kitchen, you may wish to turn off the time of day clock display on your oven.

Touch the TIMER/CLOCK pad once to turn off the time of day display. Although you will not be able to see

it, the clock maintains the correct time of day.

Touch the TIMER/CLOCK pad twice to recall the clock display.

Safety Instructions

Operating Instructions

Troubleshooting Tips

To Set the Timer

The timer does not control oven operations. The maximum setting on the timer is 9 hours and 59 minutes.

Touch the TIMER/CLOCK pad.

Touch the + or – pad until the amount of time you want shows in the display. The maximum time that can be entered in minutes is 59. Times more than 59 minutes should be changed to hours and minutes.

The timer is a minute timer only.

The CLEAR/OFF pad does not affect the timer.

If you make a mistake, touch the TIMER/CLOCK pad and begin again.

Touch the START pad. The time will start counting down, although the display does not change until one minute has passed.

When the timer reaches :00, the control will beep 3 times followed by one beep every 6 seconds until the TIMER/CLOCK pad is touched.

Support

To Reset the Timer

If the display is still showing the time remaining, you may change it by touching the TIMER/CLOCK pad, then touching the

+or – pad until the time you want appears in the display.

If the remaining time is not in the display (clock, start time or cooking time are in the display), recall the remaining time by touching the TIMER/CLOCK pad and then touching the + or – pad to enter the new time you want.

Consumer

To Cancel the Timer

Touch the TIMER/CLOCK pad twice.

8

Page 7 Page 9
Page 8
Image 8
GE JGRP20 owner manual Using the clock and timer
Page 7 Page 9

JGRP20 specifications

The GE JGRP20 is a prominent jet engine widely used in modern aviation, recognized for its efficiency, power, and advanced engineering. Developed by General Electric, this engine serves as a key component in various commercial and military aircraft, offering a blend of performance and reliability that meets the demands of today's dynamic air transport sector.

One of the primary features of the JGRP20 is its advanced turbofan design, which allows for improved fuel efficiency and lower emissions compared to older engine models. The engine incorporates cutting-edge materials such as advanced composites and titanium alloys, which contribute to its lightweight structure while ensuring durability and longevity. This makes the JGRP20 an environmentally friendly choice, aligning with global efforts to reduce the carbon footprint of aviation.

The engine boasts a high bypass ratio, which enhances its thrust capabilities while operating at lower noise levels. This is particularly advantageous for urban airports where noise regulations are stringent. The combination of high bypass ratio and advanced aerodynamics enables the JGRP20 to deliver superior performance during takeoff and cruising phases of flight.

Advanced technologies integrated into the GE JGRP20 include digital engine control systems, which optimize performance and efficiency throughout the flight. With real-time monitoring and data analysis, the engine can adapt to varying flight conditions, ensuring optimal fuel consumption and thrust. Furthermore, the engine's component health monitoring system provides invaluable insights into the operational status, allowing for predictive maintenance and minimizing downtime.

In terms of operational versatility, the JGRP20 can be tailored to suit a range of aircraft configurations, making it a flexible solution for airlines and military operators alike. Its capacity for various thrust settings allows it to power a wide array of aircraft from regional jets to larger commercial airliners.

In summary, the GE JGRP20 represents the pinnacle of jet engine design and technology. With its commitment to efficiency, reduced emissions, and noise reduction, alongside its robustness and adaptability, it stands as a trusted choice for aviation stakeholders seeking reliable and high-performing engines for their fleets. This engine not only exemplifies GE's engineering prowess but also highlights the industry's ongoing evolution towards more sustainable air travel practices.
Top Page Image Contents