www.GEAppliances.com

 

 

Control Panel

 

It’s a good idea to wipe the control panel

Do not use abrasive cleansers, strong liquid

after each use of the oven. Clean with

cleaners, plastic scouring pads or oven

mild soap and water or vinegar and water,

cleaners on the control panel—they will

rinse with clean water and polish dry with

damage the finish. A 50/50 solution of

a soft cloth.

vinegar and hot water works well.

Safety Instructions

Lift the door straight up and off the hinges.

The gasket is designed with a gap at the bottom to allow for proper air circulation.

Do not rub or clean the door gasket—it has an extremely low resistance to abrasion.

If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

Lift-Off Oven Door

The oven door is removable, but it is heavy. You may need help removing and replacing the door. Do not lift the door by the handle. This can cause the glass to break or can cause damage to the door.

To remove the door, open it a few inches to the special stop position that will hold the door open. Grasp firmly on each side and lift the door straight up and off the hinges.

NOTES:

Be careful not to place hands between the hinge and the oven door frame as the hinge could snap back and pinch fingers.

While working in the oven area, cover the hinges with towels or empty paper towel rolls to prevent pinched fingers and chipping the porcelain enamel on the frame.

To replace the door, make sure the hinges are in the special stop position. Position the slots in the bottom of the door squarely over the hinges. Then lower the door slowly and evenly over both hinges at the same time. If the hinges snap back against the oven frame, pull them back out.

To clean the inside of the door:

Do not allow excess water to run into any holes or slots in the door.

Because the area inside the gasket is cleaned during the self clean cycle, you do not need to clean this by hand. Any soap left on the liner causes additional stains when the oven is heated.

The area outside the gasket can be cleaned with a soap-filled plastic scouring pad.

To clean the outside of the door:

Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse well. You may also use a glass cleaner to clean the glass on the outside of the door.

Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When the surface is cool, clean and rinse.

Do not use oven cleaners, cleansing powders or harsh abrasives on the outside of the door.

Operating Instructions

Troubleshooting Tips

Consumer Support

27

Page 27
Image 27
GE JGRP20 owner manual Control Panel, Lift-Off Oven Door, To clean the inside of the door, To clean the outside of the door

JGRP20 specifications

The GE JGRP20 is a prominent jet engine widely used in modern aviation, recognized for its efficiency, power, and advanced engineering. Developed by General Electric, this engine serves as a key component in various commercial and military aircraft, offering a blend of performance and reliability that meets the demands of today's dynamic air transport sector.

One of the primary features of the JGRP20 is its advanced turbofan design, which allows for improved fuel efficiency and lower emissions compared to older engine models. The engine incorporates cutting-edge materials such as advanced composites and titanium alloys, which contribute to its lightweight structure while ensuring durability and longevity. This makes the JGRP20 an environmentally friendly choice, aligning with global efforts to reduce the carbon footprint of aviation.

The engine boasts a high bypass ratio, which enhances its thrust capabilities while operating at lower noise levels. This is particularly advantageous for urban airports where noise regulations are stringent. The combination of high bypass ratio and advanced aerodynamics enables the JGRP20 to deliver superior performance during takeoff and cruising phases of flight.

Advanced technologies integrated into the GE JGRP20 include digital engine control systems, which optimize performance and efficiency throughout the flight. With real-time monitoring and data analysis, the engine can adapt to varying flight conditions, ensuring optimal fuel consumption and thrust. Furthermore, the engine's component health monitoring system provides invaluable insights into the operational status, allowing for predictive maintenance and minimizing downtime.

In terms of operational versatility, the JGRP20 can be tailored to suit a range of aircraft configurations, making it a flexible solution for airlines and military operators alike. Its capacity for various thrust settings allows it to power a wide array of aircraft from regional jets to larger commercial airliners.

In summary, the GE JGRP20 represents the pinnacle of jet engine design and technology. With its commitment to efficiency, reduced emissions, and noise reduction, alongside its robustness and adaptability, it stands as a trusted choice for aviation stakeholders seeking reliable and high-performing engines for their fleets. This engine not only exemplifies GE's engineering prowess but also highlights the industry's ongoing evolution towards more sustainable air travel practices.