Using the clock, timer and control lockout

Using the clock, timer and control lockout.

ge.com

Safety

Make sure the clock is set to the correct time of day.

To Set the Clock

The clock must be set to the correct time of day for the automatic oven timing functions to work properly. The time of day cannot be changed during a timed baking or self-cleaning cycle.

Press the CLOCK pad.

Press the number pads.

Press the START pad.

Instructions

The timer is a minute timer only.

The timer does not control oven operations. The maximum setting on the timer is 9 hours and 59 minutes.

To Set the Timer

Press the KITCHEN TIMER ON/OFF pad.

Press the number pads until the amount of time you want shows in the display. For example, to set 2 hours and 45 minutes, press 2, 4 and 5 in that order.

If you make a mistake press the KITCHEN TIMER ON/OFF pad and begin again.

Press the START pad.

After pressing the START pad, SET disappears; this tells you the time is counting down, although the display does not change until one minute has passed. Seconds will not be shown in the display until the last minute is counting down.

When the timer reaches :00, the control will beep 3 times followed by one beep every 6 seconds until the KITCHEN TIMER ON/OFF pad is pressed.

The 6-second tone can be canceled by following the steps in the Special features of your oven control section under Tones at the End of a Timed Cycle.

Operating Instructions Care and

To Reset the Timer

If the display is still showing the time remaining, you may change it by pressing the KITCHEN TIMER ON/OFF pad, then press the number pads until the time you want appears in the display.

If the remaining time is not in the display (clock, delay start or cooking time are in the display), recall the remaining time by pressing the KITCHEN TIMER ON/OFF pad and then pressing the number pads to enter the new time you want.

Cleaning

To Cancel the Timer

Press the KITCHEN TIMER ON/OFF pad twice.

Troubleshooting

Control Lockout

Your control will allow you to lock out the press pads so they cannot be activated when pressed.

To lock/unlock the controls:

Press the 9 and 0 pads at the same time for 3 seconds, until the display shows LOC ON.

To unlock the control, press the

9and 0 pads at the same time for

3seconds, until the display shows

LOC OFF.

When this feature is on and the press pads are pressed, the control will beep and the display will show LOC ON.

■The control lockout mode affects all press pads. No press pads will work when this feature is activated.

■The adjustment will be retained in memory after a power failure.

Tips Consumer Support

JD900, JS900 specifications

The GE JS900 and JD900 are advanced gas turbine models from General Electric, designed for efficiency and performance in power generation. These turbines represent the innovative spirit of GE, incorporating cutting-edge technologies to meet the demands of modern energy markets.

The GE JS900 is a versatile model used primarily in combined cycle power plants. One of its standout features is its ability to achieve high thermal efficiency, reaching levels of around 60 percent. This efficiency translates into lower fuel consumption and reduced emissions, making it an environmentally friendly choice for energy producers. The JS900 utilizes a larger aerodynamic blade design and advanced cooling techniques, which enable it to operate at higher temperatures, thus enhancing its overall performance.

On the other hand, the GE JD900 is designed for industrial applications, particularly in the oil and gas sector. It boasts a robust construction that can withstand the harsh conditions typical within these environments. The JD900 features a unique combustion system that minimizes nitrogen oxide emissions while maintaining a high power output. Its modular design allows for easier maintenance and faster installation compared to other models, making it a preferred choice for operators looking for operational efficiency.

Both turbines are equipped with GE's Digital Wind Farm technology, which utilizes real-time data analysis to optimize performance and reliability. This technology allows operators to monitor and adjust settings dynamically, ensuring maximum efficiency and reducing downtime. Additionally, the JD900 and JS900 both feature advanced control systems that enable seamless integration with existing power plant operations.

Both models also emphasize flexibility in fuel options. They can operate on a variety of fuels, including natural gas, liquid fuels, and even biofuels, which adds to their adaptability in different geographical locations and energy markets.

In conclusion, the GE JS900 and JD900 turbines stand at the forefront of gas turbine technology, embodying efficiency, sustainability, and adaptability. Their advanced features, combined with GE's commitment to innovation, make them ideal choices for a variety of energy applications, meeting the needs of industries while promoting environmental responsibility.

GE JD900, JS900 owner manual Using the clock, timer and control lockout, Tips Consumer Support

Models: JD900 JS900