ge.com

Observe the Following Points in Canning

Safety

Right!

Wrong!

Note: Flat-bottomed canners are required for glass cooktops.

Pots that extend beyond 1″ of the surface unit’s circle are not recommended for most surface cooking. However, when canning with water-bath or pressure canner, larger-diameter pots may be used. This is because boiling water temperatures (even under pressure) are not harmful to the cooktop surfaces surrounding the surface units.

HOWEVER, DO NOT USE LARGE- DIAMETER CANNERS OR OTHER LARGE-DIAMETER POTS FOR FRYING OR BOILING FOODS OTHER THAN WATER. Most syrup or sauce mixtures—and all types of frying—cook at temperatures much higher than boiling water. Such temperatures could eventually harm the glass cooktop surfaces.

Be sure the canner fits over the center of the surface unit. If your cooktop or its location does not allow the canner to be centered on the surface unit, use smaller- diameter pots for good canning results.

Flat-bottomed canners must be used. Do not use canners with flanged or rippled bottoms (often found in enamelware) because they don’t make enough contact with the surface units and take a long time to boil water.

When canning, use recipes and procedures from reputable sources. Reliable recipes and procedures are available from the manufacturer of your canner; manufacturers of glass jars for canning, such as Ball® and Kerr® brand; and the United States Department of Agriculture Extension Service.

Remember that canning is a process that generates large amounts of steam. To avoid burns from steam or heat, be careful when canning.

NOTE: If your house has low voltage, canning may take longer than expected, even though directions have been carefully followed. The process time will be shortened by:

(1) using a pressure canner and

( 2) starting with HOT tap water for fastest heating of large quantities of water.

CAUTION:

Safe canning requires that harmful microorganisms are destroyed and that the jars are sealed completely. When canning foods in a water-bath canner, a gentle but steady boil must be maintained for the required time. When canning foods in a pressure canner, the pressure must be maintained for the required time.

After you have adjusted the controls, it is very important to make sure the prescribed boil or pressure levels are maintained for the required time.

Since you must make sure to process the canning jars for the prescribed time, with no interruption in processing time, do not can on any cooktop surface unit if your canner is not flat.

Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support

9

Page 9
Image 9
GE JD900, JS900 owner manual Safety, Observe the Following Points in Canning, Using a pressure canner

JD900, JS900 specifications

The GE JS900 and JD900 are advanced gas turbine models from General Electric, designed for efficiency and performance in power generation. These turbines represent the innovative spirit of GE, incorporating cutting-edge technologies to meet the demands of modern energy markets.

The GE JS900 is a versatile model used primarily in combined cycle power plants. One of its standout features is its ability to achieve high thermal efficiency, reaching levels of around 60 percent. This efficiency translates into lower fuel consumption and reduced emissions, making it an environmentally friendly choice for energy producers. The JS900 utilizes a larger aerodynamic blade design and advanced cooling techniques, which enable it to operate at higher temperatures, thus enhancing its overall performance.

On the other hand, the GE JD900 is designed for industrial applications, particularly in the oil and gas sector. It boasts a robust construction that can withstand the harsh conditions typical within these environments. The JD900 features a unique combustion system that minimizes nitrogen oxide emissions while maintaining a high power output. Its modular design allows for easier maintenance and faster installation compared to other models, making it a preferred choice for operators looking for operational efficiency.

Both turbines are equipped with GE's Digital Wind Farm technology, which utilizes real-time data analysis to optimize performance and reliability. This technology allows operators to monitor and adjust settings dynamically, ensuring maximum efficiency and reducing downtime. Additionally, the JD900 and JS900 both feature advanced control systems that enable seamless integration with existing power plant operations.

Both models also emphasize flexibility in fuel options. They can operate on a variety of fuels, including natural gas, liquid fuels, and even biofuels, which adds to their adaptability in different geographical locations and energy markets.

In conclusion, the GE JS900 and JD900 turbines stand at the forefront of gas turbine technology, embodying efficiency, sustainability, and adaptability. Their advanced features, combined with GE's commitment to innovation, make them ideal choices for a variety of energy applications, meeting the needs of industries while promoting environmental responsibility.