Instructions

Using the oven.

To avoid possible burns, place the shelves in the desired position before you turn the oven on.

Safety

 

Operating Instructions

 

The oven has 4 shelf positions.

Before you begin…

The shelves have stops, so that when placed correctly on the supports, they will stop before coming completely out, and will not tilt.

When placing and removing cookware, pull the shelf out until it stops.

To remove a shelf, pull it toward you, tilt the front end up and pull it out.

To replace, place the end of the shelf (stop-locks) on the support, tilt up the front and push the shelf in.

CAUTION: When you are using the shelf in the lowest position (A), you will need to use caution when pulling the shelf out. We recommend that you pull the shelf out several inches and then, using two pot holders, pull the shelf out by holding the sides of it. The shelf is low and you could be burned if you place your hand in the middle of the shelf and pull all the way out. Be very careful not to burn your hand on the door when using the shelf in the lowest position (A).

How to Set the Oven for Baking or Roasting

Care and Cleaning

Tips

Press the BAKE pad.

Press the INCREASE or DECREASE pad to set the oven temperature.

To change the oven temperature during the Bake cycle, press the BAKE pad and set the new temperature.

Press the START pad. When the oven starts to heat, the changing temperature will be in the display. The display starts changing once the temperature reaches 100°F.

Press the CLEAR/OFF pad when baking is finished.

Type of Food

Shelf Position

Frozen pies (on cookie sheet)

B or C

Angel food cake,

A

bundt or pound cakes

 

Biscuits, muffins, brownies,

B or C

cookies, cupcakes,

 

layer cakes, pies

 

Casseroles

B or C

Turkey

A

Troubleshooting

Preheating and Pan Placement

Preheat the oven if the recipe calls for it. Preheating is necessary for good results when baking cakes, cookies, pastry and breads.

To preheat, set the oven at the correct temperature. The control will beep when the oven is preheated and the display will show your set temperature.

This will take approximately 10–15 minutes.

Baking results will be better if baking pans are centered in the oven as much as possible. If baking with more than one pan, place the pans so each has at least 1 to 11⁄2″ of air space around it. Stagger pans on the rack so one is not directly over the other.

Consumer Support

Cut slits in the foil just like the grid.

14

Aluminum Foil

You can use aluminum foil to line the broiler pan and broiler grid. However, you must mold the foil tightly to the grid and cut slits in it just like the grid.

Without the slits, the foil will prevent fat and meat juices from draining into the broiler pan. The juices could become hot enough to catch on fire. If you do not cut the slits, you are essentially frying, not broiling.

Do not use aluminum foil on the bottom of the oven.

Never entirely cover a shelf with aluminum foil. This will disturb the heat circulation and result in poor baking.

A smaller sheet of foil may be used to catch a spillover by placing it on a lower shelf several inches below the food.

Page 13 Page 15
Page 14
Image 14
GE JSP34, JSP26 owner manual Using the oven, Tips, Troubleshooting
Page 13 Page 15

JSP26, JSP34 specifications

The GE JSP34, JSP26, JSP31, and JSP28 are cutting-edge jet engine models developed by General Electric, designed to power the next generation of commercial and military aircraft. Each model incorporates advanced technologies and innovative features that enhance performance, efficiency, and reliability.

The JSP34 engine is characterized by its high thrust-to-weight ratio, making it ideal for high-performance aircraft. It utilizes a new composite fan blade design that reduces weight while increasing aerodynamic efficiency. The advanced turbofan architecture allows for lower noise emissions and improved fuel efficiency. Additionally, the JSP34 is equipped with smart engine health monitoring systems, enabling proactive maintenance scheduling and minimizing downtime.

The JSP26 model is tailored for regional jets and smaller commercial aircraft. It features a state-of-the-art bypass ratio, providing exceptional fuel efficiency for short-haul flights. One of its standout technologies is the variable area nozzle, which optimizes performance across various flight regimes. The JSP26's modular design ensures easier maintenance and quicker turnaround times, crucial for regional operators.

The JSP31 engine focuses on versatility and adaptability, making it suitable for both commercial and military applications. Its multi-modal operation capability allows for a seamless transition between different mission profiles. The engine incorporates adaptive control technologies that optimize performance based on altitude and weight, ensuring superior operational efficiency. Enhanced materials and thermal barrier coatings contribute to improved durability and longevity, catering to the demands of varied operational environments.

Lastly, the JSP28 is designed with an emphasis on sustainability and the reduction of environmental impact. Its advanced blade materials and aerodynamic shapes contribute to reduced fuel consumption and lower CO2 emissions. The JSP28 engine features noise-reducing technologies that meet stringent regulatory requirements while enhancing passenger comfort. Furthermore, it is compatible with sustainable aviation fuels (SAFs), aligning with global initiatives aimed at fostering greener aviation practices.

In summary, the GE JSP34, JSP26, JSP31, and JSP28 engines represent significant advancements in aviation technology, each tailored to meet specific operational needs while achieving impressive performance metrics, fuel efficiency, and environmental sustainability. As the aviation industry continues to evolve, these engines embody the future of flight with their innovative characteristics and technologies.
Top Page Image Contents