3.COMPONENT TEST PROCEDURE

•High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle.

•It is neither necessary nor advisable to attempt measurement of the high voltage.

•Before touching any oven components or wiring, always unplug the oven from its power source and discharge the capacitor.

1.High voltage transformer

1)Remove connections from the transformer terminals and check continuity.

2)Normal readings should be as follows :

Secondary winding ... Approx. 110 Ω ±10% (100 Ω ±10% ÷ KOR-1B4H9A04) Filament winding ... Approx. 0 Ω

Primary winding ... Approx. 1 Ω

2.High voltage capacitor

1)Check continuity of capacitor with meter on the highest OHM scale.

2) A normal capacitor will show continuity for a short time, and then indicate 10MΩ once the capacitor charged.

3)A shorted capacitor will show continuous continuity.

4)An open capacitor will show constant 10MΩ .

5)Resistance between each terminal and chassis should be infinite.

3.High voltage diode

1)Isolate the diode from the circuit by disconnecting the leads.

2)With the ohmmeter set on the highest resistance scale measure the resistance across the diode terminals. Reverse the meter leads and again observe the resistance reading. Meter with 6V, 9V or higher voltage batteries should be used to check the front-back resistance of the diode, otherwise an infinite resistance may be read in

both directions. A normal diode's resistance will be infinite in one direction and several hundred kΩ in the other direction.

4. Magnetron

For complete magnetron diagnosis, refer to "Measurement of the Microwave Power Output." Continuity checks can only indicate and open filament or a shorted magnetron. To diagnose for an open filament or a shorted magnetron,

1)

Isolate magnetron from the circuit by disconnecting the leads.

2)

A continuity check across magnetron filament terminals should indicate 0.1 Ω or less.

3) A continuity check between each filament terminal and magnetron case should read open.

5.Fuse

If the fuse in the primary and monitor switch circuit is blown when the door is opened, check the primary and monitor switch before replacing the blown fuse. In case the fuse is blown by an improper switch operation, replace the defective switch and fuse at the same time. Replace just the fuse if the switches operate normally.

29

Page 30 Page 32
Page 31
Image 31
GE TMW-1100EC, TMW-800TC manual High voltage transformer, High voltage capacitor, High voltage diode, Magnetron, Fuse
Page 30 Page 32

TMW-1100MC, TMW-1100E, TMW-1100M, TMW-800TC, TMW-1100EC specifications

The GE TMW series of gas turbines, particularly the TMW-800T, TMW-1100EC, TMW-800TC, TMW-1100M, and TMW-1100E, represent some of the most advanced technology in power generation, designed for efficiency and reliability.

The TMW-800T is renowned for its compact design and high efficiency, making it ideal for both utility and industrial applications. This turbine boasts a modular design that facilitates ease of maintenance and installation, while its advanced aerodynamics contribute to enhanced performance and reduced emissions. Additionally, its ability to operate on multiple fuel types allows for greater operational flexibility.

Similarly, the TMW-1100EC model offers enhanced power output and efficiency. It incorporates advanced combustion technology that minimizes nitrogen oxide emissions, complying with increasingly stringent environmental regulations. The electronic control system in this model allows for superior performance management and load-following capabilities, ensuring optimal performance under varying demand.

The TMW-800TC variant focuses on achieving high thermal efficiency while maintaining significant output levels. Its cooling technologies, including advanced blade cooling techniques and heat recovery systems, enable this turbine to sustain higher operating temperatures, improving its overall efficiency. This design is particularly beneficial in combined cycle power plants, where waste heat can be repurposed to generate additional electricity.

The TMW-1100M is particularly noteworthy for its versatility and adaptability in a wide range of applications, from cogeneration to standalone power generation. Its design includes robust materials and components engineered to withstand rigorous operating conditions, ensuring longevity and reliability, which is essential for industrial users who depend on consistent power availability.

Lastly, the TMW-1100E emphasizes operational efficiency through its advanced control systems and intelligent monitoring. This turbine is equipped with sensors and software that provide real-time data analytics, allowing for proactive maintenance and operational optimization. This technology not only enhances performance but also contributes to lower operational costs.

In summary, the GE TMW gas turbine series, with their various models, exemplify cutting-edge technology and engineering. Their main features include high efficiency, reduced emissions, operational flexibility, and advanced control systems, making them a preferred choice for power generation in both industrial and utility markets. Their adaptability to different fuels and operational environments further solidifies their stance as leading solutions in the gas turbine landscape.
Top Page Image Contents