Start a wash load
Control Panel/Operation — ZBD6700 & ZBD6900
Dishwasher
3.SMART DRY— When selected, sensors detect the presence of rinse aid and the final rinse temperature. The drying heater and fan are then turned on for the minimum time to achieve optimum drying results. This saves energy as compared to conventional heated dry and saves time as compared to
4.WATER TEMP— This button provides extra heat options to increase water temperature for optimum performance.
NORMAL This is the default
HIGH |
|
|
|
|
| This water temp selection provides a wash and rinse with water temperatures | ||
|
|
|
|
|
|
|
| up to 135°F (57°C) in the NORMAL cycle and 155°F (68°C) in POTS & |
|
|
|
|
|
|
|
| PANS. Use this option for heavily soiled dishes. Cannot be used with RINSE |
|
|
|
|
|
|
|
| ONLY or CHINA CRYSTAL. |
|
|
|
|
|
|
|
| |
SANI |
|
|
|
|
|
| This water temp selection provides a sanitizing wash and rinse with water | |
|
|
|
|
|
|
|
| temperatures up to 160°F (71°C) in the NORMAL cycle and 171°F (77°C) in |
|
|
|
|
|
|
|
| POTS & PANS. Cannot be used with RINSE ONLY or CHINA CRYSTAL. At |
|
|
|
|
|
|
|
| the end of the WASH cycle, the SANI OPTION light will remain illuminated |
|
|
|
|
|
|
|
| to indicate that the sanitization conditions have been met. |
|
|
|
|
|
|
|
|
|
|
|
|
| D | E | N |
| NSF INTERNATIONAL |
|
| S | I |
|
| T | I | |
| E |
|
|
|
|
| A |
|
|
|
|
|
|
|
|
| |
R |
|
|
|
|
|
| L | Meets NSF Standard 184 Sanitization and Cleaning performance |
|
|
|
|
|
|
|
| of household |
|
|
|
|
|
|
|
|
|
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
5.DELAY
•Select the delay start time you want by pressing the DELAY START button. Multiple pressing will alternate the delay time between 2, 4 or 6 hours and OFF.
To start the dishwasher, close the door until it locks in place. The last used cycle will be displayed. To begin this cycle, push the START button. To select a different cycle, push the desired Cycle Selection and Option buttons, and then press the START button.
The door must be closed and latched into place to select a cycle or an option.
To interrupt/pause a cycle, press the selected cycle button. The Status Indicators will flash.
CAUTION: Be careful when opening the door; the hot steam that escapes when the door is opened may cause injuries. Stand back as you open the door and allow the steam to escape.
ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui s’échappe lorsque vous ouvrez la porte pendant un programme de lavage peut causer des brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur s’échapper de l’appareil.
To restart the wash process, close the door until it locks in place.
To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds. The dishwasher will then drain and the cycle indicator lights will flash. At this point a new wash cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after the dishwasher drains. If you have selected a new wash cycle, remember to add more detergent to the detergent compartment if required.
13