Design Guide
THE INSTALLATION SPACE
DIMENSIONS AND CLEARANCES
The finished
Finished Width
Wall View |
35"
Case Width
Case Depth
cutout width must be
Finished
Opening
|
|
| 6" |
|
|
|
|
| |||||||
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| 10" |
|
|
| Electrical |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| Area |
|
|
| 75" From | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 24" Cutout Depth |
|
|
| Floor to Bottom | |||||||||
|
|
|
|
| of Electrical Area | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 5" |
|
|
| Water Supply |
| 5" |
|
| ||||||
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*84" From Floor to Top Frame
36" Frame to Frame Width
*Shipping height. The refrigerator can be adjusted to fit into a cutout that is
3 1/2" | 3 1/2" |
Water And Electrical Locations
Electrical and water supply must be located as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot exceed the 24" installation depth shown. The top case trim overlaps the bottom of the soffit.
Additional Specifications
•A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded
Note: GFI (ground fault interrupter) is not recommended.
•Water line can enter the opening through the floor or back wall. The water line should be 1/4" O.D. copper tubing or GE SmartConnect™ kit between the cold water line and water connection location, long enough to extend to the front of the refrigerator. Installation of an easily accessible
Depth Including Handles:
Product Clearances
These refrigerators are equipped with a
|
| 130° Door Swing | 90° Door Swing | ||||||||||||||
|
|
|
|
| 25" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Minimum |
|
|
|
| 23 | ||||||||
|
|
|
| to Wall |
|
|
|
| Behind | ||||||||
|
|
|
|
|
|
|
|
|
|
|
| Frame | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
| 130° |
|
|
|
|
| 90° |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Allow 25" minimum clearance for a full | 4" Minimum | |||||||||||||||
| to Wall | ||||||||||||||||
| 130° door swing. Allow 15" for pan removal. |
4" minimum clearance is required when door swing is adjusted to 90°. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
See illustrations pages 4 and 5 to determine door swing interaction with adjacent cabinets or countertops.
ZUG2, ZUGSS2 Unified Grille Panel Kit
•If you are installing two refrigerators, side by side, the installation space must be
Note: Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout to calculate
•The water and electrical locations for each product must be located as shown.
•A separate 115V, 60Hz., 15 or 20 amp power supply is recommended for each product.
10"
Opening
5" Water Supply
26"
|
|
|
|
|
|
|
|
|
|
|
| Wall View | |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| 6" |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10"
75" From
Floor to Bottom
of Electrical Area
Water Supply 5"
26"
3