Installation Instructions
MAKING ELECTRICAL CONNECTIONS
• Connect the switchbox DC Input Connector to the refrigerator’s DC Input connector.
• Connect the switchbox DC Output Connector to the refrigerator’s DC Output connector.
Kit DC Input |
| |
Connector |
| |
(2 holes) | Kit DC | |
Kit DC Output | ||
Connectors | ||
Connector |
| |
(2 prongs) |
|
Refrigerator DC Connectors
•Route the switchbox wires through the wire straps already attached to the evaporator housing. Arrange the connectors as far back in the refrigerator as possible. If necessary, use the wire ties included with the kit to dress the wires.
•Cover any exposed wiring on the refrigerator connectors with UL approved electrical tape.
48” Model Shown
•Write the installation date on the ZSAB1 switchbox.
•Place the Sabbath Mode Product Kit Technical Data Sheet with the refrigerator’s Technical Data Sheet for future use.
•Close grille panel.
WARNING: No wires are to be exposed. | • Replace house fuses or reset circuit breaker. | ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Wire |
| Strap |
48” Models | 36” & 42” Models |
OPERATION CHECKLIST
With the Sabbath Switch set to OFF:
Make sure the green LED light is off. | Open the fresh food and freezer doors and confirm | |
Make sure the dispenser is operating normally. | that the interior lights, the temperature display and | |
Listen to make sure the compressor is running. | the Climate Control Drawer all operate normally. | |
If the interior lights do not come on, the Master Light | ||
| ||
| Switch may have been accidentally set to the OFF | |
| position. Make sure the Master Light Switch is in | |
| the ON position. |
With the Sabbath Switch set to ON:
Make sure the green LED light is on. | Listen to make sure the compressor is running. |
Open the fresh food and freezer doors to make sure | Confirm that the kit wires are properly routed and that |
the lights do not come on and the temperature and | no AC wires are exposed at the unit connector side. Use |
Climate Control Drawer displays do not come on. | UL approved electrical tape to cover wires completely. |
Press the temperature and Climate Control Drawer | Confirm that the Sabbath Mode Product Kit Technical |
controls to make sure they do not light up or beep. | Data Sheet has been placed with the refrigerator’s |
Try to dispense water or ice from the dispenser. | Technical Data Sheet for future use. |
Ice or water should not dispense. | Confirm that the installation date has been written |
Press the dispenser controls to make sure they | on the ZSAB1 switchbox. |
do not light up. | Leave the Installation Instructions with the consumer |
| for future use. |
7