Gemini CDMP-6000 manual JOG Wheel The JOG Wheel controls three JOG MODES, these, Stick

CDMP-6000

FUNCTIONS: (CONTINUED)

11	JOG WHEEL: The JOG WHEEL controls three JOG MODES, these
	modes are PITCH BEND, SEARCH and SCRATCH EFFECT (see JOG
	MODE BUTTON and SCRATCH BUTTON below).
12	JOG/ SCRATCH MODE: The JOG MODE button allows you to choose be-
	tween (2) of the (3) JOG MODES a JOG MODE LED indicator located be-
	tween the JOG MODE and SCRATCH BUTTONS indicates which mode
	is selected. When the LED is NOT ILLUMINATED the wheel is in PITCH
	BEND mode and can be used to speed up or slow down the track (depend-
	ing on its PITCH setting). Press the JOG MODE button once and the JOG
	MODE LED will illuminate indicating the JOG WHEEL is in SEARCH
	MODE, you may then use the wheel to skip forward or backward in the
	song. The SCRATCH button engages the units SCRATCH mode, once
	pressed the JOG MODE LED will flash indicating the unit is in SCRATCH
	MODE you may then use the JOG WHEEL to manipulate the simulated
	scratch. You may press the SCRATCH button or the JOG MODE button at
	any time to exit SCRATCH mode.
13	DISPLAY: The DISPLAY shows the playback search bar, track number,
	pitch value, pitch bend, single on/off (off for continuous play), loop, BPM,
	play/pause, time display, repeat and USB/CD modes as well as track and
	folder name and CD TEXT or track number as well as two different TIME
	display modes (SEE TIME BELOW). Time is measured in minutes, sec-
	onds and frames.
14	TIME: The TIME BUTTON switches the time display between two available
	sources, these two are TIME ELAPSED on the track, which counts how
	long the track has been playing and TIME REMAINING ON TRACK which
	counts down the time that is left before the end of the track.
15	SINGLE: Pressing the SINGLE button engages SINGLE mode, this mode
	will play one song and then stop. Pressing the SINGLE button again will
	then activate CONTINUOUS mode causing the unit to play continuously
	until the last track on the CD or currently selected FOLDER (See TRACK
	SELECTION ROTARY for additional functions).
16	BPM: Press and hold the BPM button to turn on the BPM read out, once
	on you may TAP the button to the beat of the music, after a few TAPS the
	display will read out the average BEATS PER MINUTE of the track. If there
	is a BPM value present in the MP3’s ID3-tagit will be displayed, if there is
	none it will display 0 until you TAP the value in.
17	BACK: The BACK button is used when navigating through folders. When
	pressed ONCE it will navigate one level BACK, To navigate to the ROOT
	level or beginning PRESS and HOLD the BACK button.
18	PITCH: Press and hold the PITCH button to activate the PITCH
	CONTROL SLIDE. The PITCH button has three settings 8%, 12% and
	24% and can be toggled by pressing the PITCH button once for each set-
	ting. Press and hold the PITCH button again to deactivate this mode.
19	PITCH CONTROL SLIDE: This slide, when pushed towards the bottom of
	the unit (+), increases the tempo of playback. When the slide is pushed to-

wards the top of the unit (-), the tempo of playback is decreased.

20 PITCH BEND: Pushing the PITCH BEND BUTTONS will automati- cally bend the pitch up to +24% or bend the pitch down to -24%de- pending on the setting of the PITCH BUTTON. Releasing the buttons will return the pitch to the original pitch setting. You can use this func- tion to match the beat when mixing from one song to another.

LOOP SECTION: A LOOP repeats the section between the entry point

21 (IN) and the exit point (OUT). To set a loop while the unit is playing, start by pressing the IN BUTTON (it will light up) and when you reach the desired end loop point press the OUT BUTTON (it will also light up and both will flash). The loop will continue playing until you press the OUT BUTTON again allowing the music to continue from that point on, to re-engage the loop you must press the RELOOP BUTTON. When you have released your loop the both lights will stay ON to indicate that your loop is stored in the CDMP-6000memory. Pressing the IN BUT- TON again while the unit is playing will erase the previously saved loop while saving your new loop entry point. Press OUT to exit the loop and save a new complete loop. Press RELOOP to return to the beginning of the previously saved loop from normal play. Press RELOOP repeat- edly to cause the loop to stutter.

22 PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON causes the operation to change from PLAY to PAUSE or from PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit when in PLAY mode, while it blinks in PAUSE mode.

CUE: With the CDMP-6000, creating and memorizing cue points is

23 quick and easy. By default, when there is no CUE Point set (or memo- rized), pressing the CUE button returns the unit to the beginning of the track (0:00.00) and pauses. To set a CUE Point during playback at a time of your choice, simply press PAUSE, and then use the JOG WHEEL to make any adjustments by frame. When Play is pressed to resume playback, the CUE POINT will be stored.

REPEAT: Press the REPEAT button once to engage the ALL setting

24 which will repeat all the tracks on the CD or selected FOLDER. Press the REPEAT button again to engage the (1) setting which will repeat just the selected track. Press REPEAT a third time to disengage the repeat function.

25	USB PORT The USB port allows the connection of any USB memory
	stick*.

USB/CD SELECT BUTTON The USB/CD select button allows you to

26 toggle from the CDMP-6000internal CD drive and the memory stick* connected to the USB port.

5