1030A Operating Manual
AUDIO PRECISION 1030anec LEVEL(dBr) vs FREQ(Hz)14 JAN 94 12:34:40
100 |
|
95 | 0 |
| |
90 | 15 |
|
AUDIO PRECISION 1030anec LEVEL(dBr) vs FREQ(Hz) | 14 JAN 94 12:09:56 |
100 |
|
95
TREBLE TILT
90
BASS TILT
85
80
75
70
30
45
85
80
75
BASS
70
65100
6095
5590
20 | 100 | 1k | 10k | 20k |
Figure 4. The upper curve group shows the horizontal directivity
characteristics of the 1030A in vertical configuration measured at 1 m.
The lower curve is a 1/3 octave band power response, measured in an IEC approved reverberation chamber.
65
60
55
50
20 | 100 | 1k | 10k | 20k |
Figure 5. The curves show the effect of the bass tilt, treble tilt and bass roll-off controls on the free field response.
SYSTEM SPECIFICATIONS | CROSSOVER SECTION | AMPLIFIER SECTION |
Lower | < 52 Hz |
Upper | > 20 kHz |
Free field frequency response of system: 55 Hz - 18 kHz (± 2.5 dB)
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz:
@1m > 105 dB SPL
@0.5m > 111 dB SPL
Maximum long term RMS acoustic output in same conditions with IEC weighted noise (limited by driver unit protection circuit):
@1m > 99 dB SPL
@0.5m > 105 dB SPL
Maximum peak acoustic output per pair above console top, @ 1 m from the engineer with music
material: | > 115 dB |
Self generated noise level in free field @ 1m
on axis: < 10 dB
Harmonic distortion at 90 dB SPL @ 1m on axis:
Freq: | 60...150 Hz | < 3% |
| > 150 Hz | < 0.5% |
Drivers: Bass 170 mm (6 1/2") cone Treble 19 mm (3/4") metal dome
Both drivers are magnetically shielded.
Weight: | 7,6 kg (17 lb) | |
Dimensions: |
|
|
| Height 312 mm (12 1/4") | |
| Width | 200 mm ( 7 7/8") |
| Depth | 240 mm (9 7/16") |
Input connector XLR female:
pin 1 gnd pin 2 + pin 3 -
Input impedance: | 10 kOhm balanced |
Input level for 100 dB SPL output @ 1m: variable from +6 to
Input level for maximum short term sine wave output of 105 dB SPL @ 1m:
variable from +11 to
Subsonic filter below 50 Hz : | 18 dB/octave |
Ultrasonic filter above 25 kHz: | 12 dB/octave |
Crossover frequency, Bass/Treble: | 3.5 kHz |
Crossover acoustical slopes:
24 - 32 dB/octave
Treble tilt control operating range in 2 dB steps: from +2 to
Bass
Bass tilt control operating range in 2 dB steps: from 0 to
The 'CAL' position is with all tone controls set to 'off' and the input sensitivity control to maximum (fully clockwise).
Bass amplifier short term output power with a
4 Ohm load:
80 W
Treble amplifier short term output power with an
8 Ohm load:
50 W
Long term output power is limited by driver unit protection circuitry.
Amplifier system distortion at |
| |
nominal output: |
|
|
| THD | < 0.08% |
| < 0.08% | |
|
| < 0.08% |
| DIM 100 | < 0.08% |
Signal to Noise ratio, referred to full output: | ||
| Bass | > 95 dB |
| Treble | > 95 dB |
Mains voltage: | 230, 100/200 or 115/230V | |
| according to region | |
Voltage operating range: | ±10% | |
Power consumption: |
|
|
| Idle | 10 VA |
| Full output | 100 VA |
Genelec Document D1030AR001 Copyright Genelec Oy 3.2003. All data subject to change without prior notice
International enquiries:
Genelec, Olvitie 5
Phone +358 17 83881
Fax +358 17 812 267
Email genelec@genelec.com
| www.genelec.com |
In the U.S. please contact: | In China please contact: |
Genelec, Inc., 7 Tech Circle | Genelec China Representative Office |
Natick, MA 01760, USA | Soho New Town, 88 Jianguo Road |
Phone +1 508 652 0900 | |
Fax +1 508 652 0909 | Beijing 100022, China |
Email genelec.usa@genelec.com | Phone +86 10 8580 2180 |
| Fax +86 10 8580 2181 |
