Generac 004702-0, 004703-0, 004704-0, 004705-0, 004706-0, 004707-0 Generator Control Panel

Section 2 – Operation

QUIETPACT 55, 65, and 75 Recreational Vehicle Generators

◆1.6.4 ENGINE SPECIFICATIONS

Type of Engine
QUIETPACT 55/65/75		GT-760
Cooling Method		Air-cooled
Rated Horsepower
QUIETPACT 55		27 at 3600 rpm
QUIETPACT 65		27 at 3600 rpm
QUIETPACT 75		27 at 3600 rpm
Displacement
QUIETPACT 55/65/75		760cc
Compression Ratio		8.6 to 1
Cylinder Block		Aluminum w/Cast Iron Sleeve
Type of Governor		Mechanical, Fixed Speed
Engine Governor Speed
QUIETPACT 55		2200 rpm
QUIETPACT 65/75		2571 rpm
Air Cleaner	Paper Element w/Foam Precleaner
Starter		12-volt DC Electric
Ignition System		Solid-state w/Flywheel Magneto
Recommended Spark Plug
Champion		RC12YC
AC		R45S
Fram Autolite		65
Spark Plug Gap		0.030 inch (0.8 mm)
Recommended Min. Battery		............400 Cold Cranking Amps

◆1.6.5 EMISSIONS COMPLIANCE PERIOD

For nonhandled engines the Emissions Compliance Period referred to on the Emissions Compliance Label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements.

•For engines less than 225 cc displacement, Category C=125 hours, B=250 hours, and A=500 hours.

•For engines of 225 cc or more, Category C=250 hours, B=500 hours, and A=1000 hours.

2.1GENERATOR CONTROL PANEL

The following features are mounted on the generator control panel (Figure 2.1):

◆2.1.1 FUEL PRIMER

Before starting a cold engine (if it has not been start- ed in more than two weeks), you must press this switch for approximately ten seconds to bring fuel from the tank to the fuel pump. This rocker type switch springs back into its original position when you release it.

◆2.1.2 START/STOP SWITCH

To crank and start the engine, hold this switch in the START position. Release the switch when the engine starts. To stop an operating engine, press and hold the switch in the STOP position until the engine shuts off. The switch center position is the RUN position.

◆2.1.3 7.5 AMP FUSE

The fuse protects the engine’s DC control circuit against electrical overload. If the fuse element has melted open due to overloading, the engine cannot be cranked. If you must replace the fuse, use only an identical 7.5 amp replacement fuse.

◆2.1.4 LINE BREAKERS

Protects generator’s AC output circiut against overload, i.e., prevents unit from exceeding wattage/amperage capacity. The circuit breaker rat- ings are as follows:

Model	Circuit Breaker 1	Circuit Breaker 2	240 Volt
QuietPact 55	30A	20A	25A 2P
QuietPact 65	30A	30A	30A 2P
QuietPact 75	35A	35A	35A 2P

NOTE:

If this generator has been reconnected for dual voltage AC output (120/240 volts), you can install line breakers having an amperage rating that is different than that stated above. The replacement line breakers consist of two separate breakers with a connecting piece between the breaker handles (so that both breakers will operate at the same time). If the unit is reconnected for dual voltage, it is no longer RVIA or CSA listed.

Figure 2.1 – Typical Control Panel

CONTROL CENTER

			C I R	U I T
			B R E A K E R
			C I R	U I T
			B R	A K E R
F	S E	S T A R T	F U E L		REV. B
					0E0580
7	5 A
IF GENERATOR DOES NOT START.		S T O P	P R I M E
REMOVE AND INSPECT FUSE.

(SEE OWNER'S MANUAL TROUBLE SHOOTING GUIDE.)

PRESS PRIME SWITCH FOR 10 SECONDS

BEFORE STARTING. WHEN STARTING, DO NOT PRESS

START BUTTON LONGER THEN 15 SECONDS PER ATTEMPT.

Generac® Power Systems, Inc. 7