Manuals / Gigabyte / Computer Equipment / Network Card

Gigabyte GA-K8NF-9-RH user manual Cpufan / Sysfan Cooler Fan Power Connector, FDD FDD Connector

Models: GA-K8NF-9-RH

1 88

Download 88 pages 27.47 Kb

Page 20

English

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND).

Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to prevent CPU damage or system hanging caused by overheating.

						Pin No.	Definition
						Pin No.	Definition
						1	GND
						1	GND
	1
	1					2	+12V
	CPU_FAN
	CPU_FAN					3	Sense
						3	Sense
					1
					1

	SYS_FAN

5)FDD (FDD Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDD connector.

3433

21

GA-K8NF-9-RH Motherboard

- 20 -

Image 20

Gigabyte GA-K8NF-9-RH user manual Cpufan / Sysfan Cooler Fan Power Connector, FDD FDD Connector

Contents

GA-K8NF-9-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NF-9-RH Motherboard Layout Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary LAN4Mbit flash ROM Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Side Speaker OutATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector Pwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 14 F11394 / F21394 Front Ieee 1394 ConnectorsClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. FD F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 2/3/4/5 Master TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B Boot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Password Check Init Display FirstIDE DMA transfer access Integrated PeripheralsOn-Chip IDE Channel0 On-Chip IDE Channel1On-Chip LAN Boot ROM IDE Prefetch ModeOn-Chip MAC Lan controlled by Vitesse 8201 phy NV IDE/SATA RAID functionParallel Port Mode ECP Mode Use DMAOnboard Serial Port Onboard Parallel PortPower Management Setup Power On by Mouse Power On by KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations Current CPU Temperature PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMCPU Warning Temperature Temp of FAN turn off Default temperature 0oCCPU FAN Fail Warning CPU Smart FAN Control NoteTemp Limit of Low Speed Default temperature 20oC Temp Limit of Mid Speed Default temperature 50oCTemp Limit of High Speed Default temperature 60oC Temp of full FAN Speed Default temperature 70oCHT Frequency Ratio CPU FrequencyK8 CPU Clock Ratio Current DDR speedDDR voltage control Chipset core PCI-E voltageHT-Link voltage control Top Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Install Sata hard drives in your system Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below RAID Appendix Step Save and exit Bios Setup GA-K8NF-9-RH Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation NForce Storage Controller Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English Step Troubleshooting English English English Contact Us Taiwan HeadquartersGigabyte Global Service System