Product Specifications
GMVM96 Dimensions
|
|
| 28¾ |
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
| ¾ | |||||
¾ |
| 19⅞ |
|
| 2½ |
|
| |
|
| |||||||
|
|
|
|
|
|
|
|
|
¾
2¹/₁₆ |
2¹¹/₁₆ |
7⅜
1¾
1½
2⅝
30¼
21¼
|
|
|
|
| 4⅛ |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| 24⁹/₁₆ |
|
|
|
| 6⅛ | ||||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 27⅛ |
|
|
|
|
|
|
|
|
| |
|
|
| 2⅝ |
|
|
| |||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
30¼ |
| 19³/₁₆ |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
19³/₁₆
1¾
11¾
|
| 22 ¹/₁₆ |
| |
1⅝ |
| |||
|
|
| FOLDED FLANGES |
|
23⁹/₁₆
UNFOLDED FLANGES
LEFT SIDE VIEW
|
|
|
|
|
|
|
|
|
|
|
|
| 11¾ |
|
|
|
|
|
|
|
|
|
|
|
| 16⅝ |
| 32¹³/₁₆ |
|
|
|
|
|
| FOLDED FLANGES |
|
|
| 1¾ |
| ||||||||||
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| D |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| UNFOLDED FLANGES |
|
|
|
|
|
|
|
|
|
| |||||
|
|
| E |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| RIGHT SIDE VIEW | |||||||||||
| FRONT VIEW |
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model | W | D | H |
GMVM960603BX | 17½” | 28¾" | 40¾" |
GMVM960805CX | 21" | 28¾" | 40¾" |
|
|
|
|
GMVM961005DX | 24½” | 28¾" | 40¾" |
|
|
|
|
GMVM961155DX | 24½” | 28¾" | 40¾" |
|
|
|
|
A | B | C | D | E |
17½” | 16" | 13⅛" | 12⅛" | 13⅝" |
21" | 19½” | 16⅛" | 16" | 17½” |
|
|
|
|
|
24½” | 23" | 20⅝" | 19⅜" | 20⅞" |
|
|
|
|
|
24½” | 23" | 20⅝" | 19⅜" | 20⅞" |
|
|
|
|
|
Notes:
•Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required). Vent pipe must be either 2” or 3” in diameter, depending upon furnace input, number of elbows, length of run and installation
(1 or 2 pipes). The optional Combustion Air Pipe is dependent on installation/code requirements and must be 2” or 3” diameter PVC.
•Line voltage wiring can enter through the right or left side of the furnace.
•Conversion kits for
•Installer must supply following gas line fittings, according to which entrance is used:
•For bottom return: Failure to unfold flanges may reduce airflow by up to 18%. This could result in performance and noise issues.
Minimum Clearances to Combustible Materials
Position | Sides | Rear | Front | Bottom | Flue | Top |
|
|
|
|
|
|
|
Upflow | 0” | 0” | 3” | C | 0” | 1” |
|
|
|
|
|
|
|
Horizontal | 6” | 0” | 3” | C | 0” | 6” |
|
|
|
|
|
|
|
C = If placed on combustible floor, the floor MUST be wood ONLY.
Notes
•For servicing or cleaning, a 24” front clearance is required.
•Unit connections (electrical, flue and drain) may necessitate greater clearances than the minimum clearances listed above.
•In all cases, accessibility clearance must take precedence over clearances from the enclosure where accessibility clearances are greater.
4 | www.goodmanmfg.com |
