Goodman Mfg CVC9/95, MVC95 Product Description, Productapplication, Features

PRODUCT DESCRIPTION & APPLICATION

WARNING

TO PREVENT PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO FIRE, DO NOT INSTALL THIS FURNACE IN A MOBILE HOME, TRAILER, OR RECREATIONAL VEHICLE.

PRODUCT DESCRIPTION

FEATURES

This furnace is a part of the ComfortNet™ family of products. The CTK01 ComfortNet thermostat kit allows this furnace to be in- stalled as part of a digitally communicating system. The ComfortNet system provides automatic airflow configuration, enhanced setup features, and enhanced diagnostics. It also reduces the number of thermostat wires to a maximum of four. It may be also installed as part of a “legacy” system using a standard 24 VAC thermostat.

This product may also be installed with the ComfortNet thermostat and a non-ComfortNet compatible single stage air conditioning unit. However, this reduces the benefits of the ComfortNet system as the enhancements will only apply to the furnace.

PRODUCTAPPLICATION

This furnace is primarily designed for residential home-heating ap- plications. It is NOT designed or certified for use in mobile homes, trailers or recreational vehicles. Neither is it designed or certified for outdoor applications. The furnace must be installed indoors (i.e., attic space, crawl space, or garage area provided the garage area is enclosed with an operating door).

This furnace can be used in the following non-industrial commer- cial applications:

Schools,Officebuildings,Churches,Retailstores,

Nursinghomes,Hotels/motels,Commonorofficeareas

In such applications, the furnace must be installed with the follow- ing stipulations:

•It must be installed per the installation instructions provided and per local and national codes.

•It must be installed indoors in a building constructed on site.

•It must be part of a ducted system and not used in a free air delivery application.

•It must not be used as a “make-up” air unit.

•It must be installed with two-pipe systems for combustion air, especially if VOC’s or other contaminants are present in the conditioned space.

•All other warranty exclusions and restrictions apply This furnace is an ETL dual-certified appliance and is appropriate for use with natural or propane gas (NOTE: If using propane, a propane conversion kit is required).

Dual certification means that the combustion air inlet pipe is op- tional and the furnace can be vented as a:

Non-direct vent (single pipe) central forced air furnace in which combustion air is taken from the installation area or from air ducted from the outside or,

Direct vent (dual pipe) central forced air furnace in which all combustion air supplied directly to the furnace burners through a special air intake system outlined in these instructions.

This furnace may be used as a construction site heater ONLY if all of the following conditions are met:

•The vent system is permanently installed per these installation instructions.

•A room thermostat is used to control the furnace. Fixed jumpers that provide continuous heating CANNOT be used and can cause long term equipment damage.

•Return air ducts are provided and sealed to the furnace.

•A return air temperature range between 60ºF (16ºC) and 80ºF (27ºC) is maintained.

•Air filters are installed in the system and maintained during construction replaced as appropriate during construction, and upon completion of construction.

•Theinputrateandtemperaturerise aresetperthefurnace rating plate.

•100% outside air is provided for combustion air requirements during construction.Temporary ducting can be used.

NOTE: Do not connect the temporary duct directly to the furnace. The duct must be sized for adequate combustion and ventilation in accordance with the latest edition of the National Fuel Gas Code NFPA 54/ANSI Z223.1 or CAN/CSA B149.1 Installation Codes.

•The furnace heat exchanger, components, duct system, air filters and evaporator coils are thoroughly cleaned following final construction clean up.

•All furnace operating conditions (including ignition, input rate, temperature rise and venting) are verified according to these installation instructions.

NOTE: The Commonwealth of Massachusetts requires that the following additional requirements must also be met:

•Gas furnaces must be installed by a licensed plumber or gas fitter.

•A T-handle gas cock must be used.

•If the unit is to be installed in an attic, the passageway to and the service area around the unit must have flooring.

To ensure proper furnace operation, install, operate and maintain the furnace in accordance with these installation and operation instructions, all local building codes and or- dinances. In their absence, follow the latest edition of the Na- tional Fuel Gas Code (NFPA54/ANSI Z223.1), and/or CAN/CSA B149 Installation Codes, local plumbing or waste water codes, and other applicable codes.

7