DESIGN FEATURES
4 | 5 | 7 | 8 | 11 | 13 | 14 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 | 9 | 10 | 12 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
4 |
| 5 | 7 |
|
| 8 |
| 11 | 13 14 |
|
| ||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 | 9 | 10 |
| 12 |
|
|
|
|
|
|
|
|
|
|
|
|
| |
4 |
| 5 | 6 |
| 7 |
| 8 | 11 | 13 |
|
| 14 |
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 9 | 10 | 12 |
1. | Power LED (Top of unit - Not Shown) – This Blue LED illuminates when the unit is turned on. | |||
2. | Thermal LED (Top of unit - Not Shown) – This Red LED illuminates if the amplifier internal components | |||
3. | become too hot and engage the thermal protection.The amplifier will shut down to cool if this occurs. | |||
Protect LED (Top of unit - Not Sh wn) – ThisYellow LED illuminates if a short circuit or too low of an | ||||
4. | impedance is detected at the speaker connections.The amplifier will automatically shut down if this occurs. | |||
Cast Aluminum Heatsink – The cast aluminum heatsink of the Power amplifier dissipates heat generated by | ||||
5. | the amplifier's circuitry. |
|
| |
SpeakerTerminals – The heavy duty, | ||||
6. | 8 AWG to 18 AWG. |
|
|
|
Remote Punch EQ (Optional Controller) – The Remote Punch EQ connection is made with a | ||||
| and can be installed in a variety of ways for easy control access.The control is used to boost low and/or high | |||
| frequency information to overcome road noise.The remote overrides the Punch EQ on the amplifier when | |||
| connected. |
|
|
|
NOTE: Previous (prior to 2007) Punch Bass and | ||||
7. | Punch EQ – This control is a narrow band adjustment variable from 0dB to +18dB @ 45Hz with a Gyrator | |||
8. | based Punch EQ that eliminates frequency shift with boost. | |||
Infrasonic Filter – A 28Hz High Pass filter designed to prevent frequencies below the audio range from being | ||||
| applied to the subwoofer from the amplifier. Consequently improving subwoofer performance and power | |||
9. | handling, particularly in vented enclosures. |
|
| |
Variable Cr | – Is a | |||
10. | 250Hz.The crossover is set to |
|
| |
G in Control – The input gain control is preset to match the output of most source units. It can be adjusted to | ||||
11. | match output levels from a variety of source units. |
| ||
RCA | ||||
12. | without running an extra set of RCA cables from the front of the vehicle to the rear amplifier location. | |||
RCA Input Jacks – The industry standard RCA jacks provide an easy connection for signal level input.They are | ||||
13. | ||||
REMTerminal – The heavy duty, | ||||
| 12 AWG to 24 AWG.This terminal is used to remotely | |||
14. | applied. |
|
|
|
PowerTerminals – The power and ground are | ||||
| accommodate up to 4 AWG wire. |
|
|
4