Troubleshooting guide | Haier 29F3A specs

Troubleshooting guide

To assist in location possible faults use help guide below.

	BREAKDOWN PHENOMENON		CHECKING
	PICTURE	SOUND	CHECKING
	PICTURE	SOUND
			The aerial direction and connection
	Picture with snow	Noise
			This is called ghosting which can be minimized
			with an outside aerial, and good quality cable
			and terminations. Altering the aerial direction
	Double or Triple Image	Normal	can also minimize this effect.
	Double or Triple Image	Normal
			Electrical interference which can be caused by cars,
			motorbikes etc, Fluorescent lamps and dirty
	Disturb	Noise	insulators on overhead power cables.
	Disturb	Noise
			1. Volume Sound mute.
			2. Only 1 speaker has no sound. Press S.STD button to
			choose USER mode, then check wether the BALANCE
			item value in SOUND menu equal to 0. Adjust the
	Normal	No sound or 1	BALANCE item in SOUND menu as you wish in USER
	Normal	speaker no sound	mode.
		speaker no sound	mode.
			Ensure that the power supply is connected to the TV
			set and turned on. Also ensure that the TV set is not
		No sound	in "Listen Mode" or that the brightness and contrast
	No Picture	No sound	are not turned down.
			Adjust colour control
	No colour	Normal volume

			Adjust channel again
	Scramble	Normal or Weak Volume

			Colour Purity fault which can be caused by moving the
			TV set, placing magnets near the TV screen or turning
			on/off house hold appliances such as vacuum cleaners
			near the TV set. Turn the TV off with the mains power
	Colour Spot	Normal volume	switch for 15 minutes. When the power is turn on again
	Colour Spot		the TV set will automatically degauss the picture. In
			the TV set will automatically degauss the picture. In
			server cases leave the TV set turned off over night.

Note:

1.If the fault can not be repaired using the above guide consult with your local authorized service center.

2.The TV set must only be repaired by a qualified registered service person. Never attempt to remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire.

3.The cabinet may produce the occasional "snapping sound" This is normal and caused by the materials in the cabinet expanding with room temperature changes.

26

Image 28

Haier 29F3A manual Troubleshooting guide, To assist in location possible faults use help guide below

Contents

29F3A Page Contents Explanation on the display tube Installation Battery installationAvoid dropping the remote control and/or getting it wet Aerial connection Front and side panel of the TV set Function buttons and external socketsRear panel of the TV set Buttons on the remote control Exit screen display Switching on/ off the TV set Switching on/ off the TV setSwitching on/ off the TV set Auto switch-off function How to select TV program Watching TVWatching TV program Tune Program swap and auto scan functions Program swapAuto program scan Swap Full automatic mode Searching channelDisplay function Call Semi-automatic search Semi-automatic searchTo turn off the on-screen menu Exit If the picture and/or sound are poor, try using the Fine Manual fine tuneManual fine tune Press the CH+/- buttons to select Fine Tune If you want to recover the skipped channel Program skipPress the CH+/- buttons to Select Skip Press the VOL-/+ buttons to Turn the Skip function on How to select picture modes How to customize your own picture statusConvenient picture and sound control functions Multiple picture modes How to select Black Stretch How to select Noise ReduceBlack stretch and noise reduce Function How to choose sound mode How to customize you own sound qualityMultiple audio modes Sound How to use surround Surround and mute functionsSound mute Mute Clock setting and timer on/off functions Clock settingOn/off timer Time functions Sleep timer and program preset Sleep timer Set up function How to start screen saver functionScreen saver Childlock functions Child lock function AVL and calendar functions AVL function Fade and select a language FadeSelect a language Press the CH +/- buttons to select Fade Position exchange functions ExchangeExchange Press the CH-/+ buttons to Select Program Teletext TeletextTeletext functions Button again to revert back to Full text Teletext To outside input To video/audio input Troubleshooting guide To assist in location possible faults use help guide below Specifications Design and specifications may be changed without noticePage