Parts and Functions
|
| Indoor Unit |
| Remote controller | ||
|
| |||||
|
|
|
|
|
|
|
Inlet
Inlet grille
Outlet
Air Purifying FilterAnion generator
(inside)
Vertical blade
(adjust left and right air flow)
Horizontal flap
(adjust up and down air flow Don't adjust it manually)
1 | 6 | 6. TIMER OFF display |
| |
2 |
| TIMER ON display |
| |
7 | 7. TEMP display |
| ||
|
| |||
3 |
| 8. Additional functions display | ||
4 |
| Supplemented |
| |
| electrical | HEALTH TURBO | ||
| Operation mode QUIET SLEEP heating | |||
5 | 8 | Remote controller |
| |
9. TURBO/QUIET button | ||||
9 |
| |||
TURBO/QUIET | 18 | 10. FAN button |
|
Display board
Aureole |
|
| TEMP display | ||
Display mode,the aureole display different |
| ||||
colour when setting different function |
|
| |||
COOL: blue | FAN: yellow |
|
| ||
AUTO: white DRY: cyan | |||||
| Inlet | Air Purifying Filter (inside) | |||
Inlet grille |
|
|
|
|
|
Outlet |
|
|
|
|
|
Horizontal flap | Vertical blade |
| Emergency | ||
| Switch |
| |||
(adjust up and down air flow | (adjust left and | Display board |
| ||
Don't adjust it manually) | right air flow) |
| |||
Display board | 1 | 2 | 3 | 4 | 5 |
10 |
|
| 19 | 11. | COOL button | |
11 |
|
| 12. SWING LEFT/RIGHT button | |||
|
| 20 | ||||
|
|
| 13. FAN SPEED button | |||
12 |
|
|
| |||
SWING |
| 21 | 14. | HEALTH display | ||
|
| |||||
13 |
|
| 15. | SLEEP display | ||
|
|
| ||||
|
|
| 22 | 16. | LOCK button | |
14 | HEALTH | SLEEP |
| 17. | LIGHT button | |
|
| 23 | ||||
15 |
|
| Control the lightening and extinguishing | |||
TIME | TIME |
| ||||
ON | OFF |
| ||||
16 |
|
| 24 | of the indoor LED display board. | ||
|
|
| 18. POWER/SOFT display | |||
17 |
|
| 25 | |||
|
| 19. | DRY button | |||
|
|
| ||||
|
|
|
| 20. TEMP display | ||
|
|
|
| 21.SWING UP/DOWN button | ||
1. Mode display |
| 22. TIMER OFF/ON displa | ||||
Operation mode | AUTO COOL DRY | FAN | 23.HEALTH AIR FLOW button | |||
Remote controller |
|
|
| 24.CANCEL/CONFIRM button | ||
2. Signal sending display | ||||||
Function: Setting and cancel to the | ||||||
3. SWING | display |
| timer and other additional functions. | |||
4. FAN SPEED display | 25. | RESET button | ||||
|
|
| Display | When the remote controller appears | ||
|
|
| circulated | abnormal, use a sharp pointed | ||
LO MED |
| HI | AUTO | article to press this button to reset |
1Signal receiver hole
2ON/OFF display
3Ambient temp.display
When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed.
4TIMER ON\OFF display TIMER ON-OFF display
SLEEP display
Note to the power failure resume:
press the sleep button ten times in five seconds and enter function after hearing four sounds.And press the sleep button ten times within five seconds and leave this function after hearing two sounds.
5COOL\HEAT\Dry\AUTO display
5. LOCK display | the remote. |
Healthy function is not available for some units.
Outdoor Unit
OUTLET |
INLET |
CONNECTING PIPING |
| 1 | Inlet | 54 Air Purifying Filter (inside) | |||
2 Inlet grille |
|
|
| 8 | ||
|
|
| Emergency | |||
|
|
|
|
| ||
|
|
|
|
| Switch | |
3 | Outlet |
|
|
| 9 | |
45 | Anion generator | 6 Vertical blade | 12 | 10 | ||
11 | ||||||
| (inside) | (adjust left and |
| |||
7 | Horizontal flap |
| 13 | |||
| right air flow) |
| ||||
(adjust up and down air flow |
|
|
|
Don't adjust it manually)
9Power indicator (Lights up when unit starts.)
10 Timer mode indicator
(Lights up whenTimer operation is selected.)
11 Operation mode indicator
(lights up when the compressor is on.)
12Remote signal receiver
(A beeping sound is generated when a signal from remote controller isreceived.)
13 Ambient temp display
When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference.
Actual inlet grille may vary from the one shown in the manual according to the product purchased
2
| 4 | AND ELECTRICAL WIRING |
| 4 DRAIN HOSE | |
|
| |
Loading of the battery | ||
1 | Remove the battery cover; | |
2 | Load the batteries as illustrated. | |
| 2 | |
3 | (cylinder); | |
Be sure that the loading | ||
| is in line with the" + |
Note: 4 Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece- iver hole should be within 7m without any obstacle as well.
When
Full display or unclear display during operation indicates the batteries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later.