Operation
Base Operation
Emergency operation and test operation
Emergency Operation:
Remote controller
2
TURBO/QUIET |
|
|
|
|
|
| 11 |
|
|
| 3 |
SWING |
|
| 4 |
|
|
| |
|
| 3 | 2 |
HEALTH | SLEEP |
| |
TIME | TIME |
|
|
ON | OFF |
|
|
Use this operation only when the remote controller is defective | ||||
or lost, and with function of emergency running, air conditoner | ||||
can run automatically for a while. |
| |||
When the emergency operation switch is pressed, the " Pi " | ||||
sound is heard once, which means the start of this operation. | ||||
When power switch is turning on for the first time and | ||||
emergency operation starts, the unit will run automatically in | ||||
the following modes: |
|
| Pi | |
Room | Designated | Timer | Fan | Operation |
temperature | temperature | mode | speed | mode |
Above 23oC | 26oC | No | AUTO | COOL |
It is impossible to change the settings of temp. and fan speed,It
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
COOL button:Cooling mode FAN button: Faning mode DRY button: Dehumidify mode
3.Select temp.setting
Press | / | button |
| Every time the button is pressed, temp.setting | |
| increase 1oC,if kept depressed, it will increase | |
| rapidly |
|
| Every time the button is pressed, temp.setting | |
| decrease 1oC,if kept depressed, it will | |
| decrease | rapidly |
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
Display circulated
LOW MED | HI | AUTO |
Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.
Operation | Remote | Note | |
Mode | Controller | ||
| |||
|
| Under the mode of auto operation, air conditioner will | |
AUTO |
| automatically select Cool or Heat operation according to | |
| room temperature. When FAN is set to AUTO the air | ||
|
| conditioner automatically adjusts the fan speed according | |
|
| to room temperature. | |
COOL |
| according to room temperature. | |
DRY |
| In DRY mode , when room temperature becomes lower | |
| than temp.setting+2o C, unit will run intermittently at LOW | ||
|
| speed regardless of FAN setting. | |
|
| In FAN operation mode , the unit will not operate in COOL or | |
FAN |
| HEAT mode but only in FAN mode, AUTO is not available in | |
| FAN mode. And temp. setting is disabled. In FAN mode, | ||
|
| sleep operation is not available. |
is also not possible to operate in timer or dry mode.
Test operation:
Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room
temperature is below 16oC, do not use it in the
normal operation. | Pi Pi |
|
Continue to press the test operation
switch for more than 5 seconds . After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi".
Under this operation mode,the fan motor of indoor unit will run in high speed.
Air Flow Direction Adjustment
1.Status display of air flow
Vertical flap
Pos.1 | (Auto swing) |
Initial state
Pos.2 No initial state disaplayed on remote controller, the vertical flap will be fixed on the current position
2.Left and right air flow adjustment
For each press of button, remote controller displays as follows :
remote controller:
Pos.1 | Pos.2 | Pos.3 | Pos.4 |
Pos.5 | Pos.6 |
|
|
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur adjusted to left or at air outlet if all vertical louvers are right.
It is advisable not to keep horizontal flap at downward position for a long time in COOLor DRY mode , otherwise, condensate water might occur.
Note:
When restart after remote turning off, the remote controller controller will automatically memorize the previous set swing position.
3