Parts and Functions
Indoor Unit
EK1 display board | 1 |
|
| 3 |
| |
| 2 |
|
|
|
| 8 |
| 4 |
|
|
|
|
|
|
| 6 |
| 5 |
| 7 |
EK3 display board | 1 |
|
| 3 |
| |
| 2 |
|
|
|
|
|
| 4 |
|
|
|
|
|
| 6 |
|
| 7 | 5 | 8 |
1 | Inlet |
| 2 | Inlet grille |
| |
3 | Air Purifying Filter(inside) | 4 | Outlet |
|
| |
5 | Horizontal flap |
| 6 | Vertical blade | ||
(adjust up and down air flow. | (adjust left and right air flow) | |||||
Don't adjust it manually) |
| 8 | Emergency Switch | |||
|
|
|
7Display board
Display board
EK1EK3
2 | 4 | 5 |
4 |
|
|
6 |
|
|
Signal receiver hole | 4 TIMER ON/OFF display | |
TIMER | ||
ON/OFF display | ||
SLEEP display | ||
Ambient temp.display | Note to the power failure resume: | |
When receiving the remote control | Press the sleep button ten times in five seconds and enter function | |
after hearing four sounds.And press the sleep button ten times | ||
signal,display the set temperature | ||
within five seconds and leave this function after hearing two sounds. | ||
and in the rest time the room | ||
temperature is displayed and this | 5 COOL\HEAT\DRY\AUTO display | |
room temperature is only for reference. | 6 RUNNING display |
Please be subject to the actual produce purchased the above picture is just from your reference
Outdoor Unit
| 4 |
OUTLET | CONNECTING PIPING AND ELECTRICAL WIRING |
INLET | DRAIN HOSE |
Please be subject to the actual produce purchased the above picture is just from your reference
Remote controller
1 | 6 | 8.Additional functions display | |||
|
|
| Supplemented |
| |
|
| Operation mode QUITE SLEEP electrical | HEALTH POWER | ||
2 |
|
| heating |
| |
7 | Remote controller |
| |||
3 | 9. QUIET button |
| |||
|
| ||||
| 10. | HEAT button |
| ||
4 |
|
| |||
| 11. COOL button |
| |||
5 | 8 | 12. | AUTO button |
| |
9 |
| 13. FAN SPEED button |
| ||
18 | 14. | TIMER button |
| ||
10 |
| 15. | HEALTH button |
| |
| 16. LOCK button |
| |||
11 | 19 |
| |||
Used to lock buttons and LCD display. | |||||
|
2017. LIGHT button
12 | Control the lightening and extinguishing | |
of the indoor LED display board. | ||
| ||
13 | 21 18. POWER ON/OFF button | |
| 19. DRY button |
2220. TEMP button
14 |
| 23 | 21. SWING button | |
15 |
| 22. HOUR button | ||
16 |
| 24 23. EXTRA FUNCTION button | ||
|
| Function: Air | ||
17 |
| 25 | airflow | |
|
|
| position 2 | |
1. Mode display |
| flap position | ||
Operation mode | AUTO COOL | DRY HEAT FAN | ||
Remote controller |
|
| displayed | |
2. Signal sending display | ||||
(reserved function) | ||||
3. SWING display |
| |||
| Fahrenheit/Celsius mode conversion | |||
4. FAN SPEED display | 24.CANCEL/CONFIRM button | |||
|
|
| ||
|
| Display | Function: Setting and cancel to the | |
LO MED | HI | circulated | timer and other additional functions. | |
AUTO | 25. RESET button | |||
5. LOCK display |
| |||
| When the remote controller | |||
6. TIMER OFF display | appears abnormal, use a sharp | |||
TIMER ON display | pointed article to press this button | |||
7.TEMP display |
| to reset the remote |
Healthy function is not available for some units.
Loading of the battery
1Remove the battery cover;
2 Load the batteries as illustrated. 2
(cylinder);
3 Be sure that the loading is in line with the" +
4 Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece- iver hole should be within 7m without any obstacle as well.
When
Full display or unclear display during operation indicates the batteries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later.
Hint:
Remove the batteries in case won't be in use for a long period. If there is any display after
1