Haier HWM88-0566T Safety precautions, Trouble-shooting answer to question, Common phenomena

Safety precautions

Please plug the power plug on special		The washing machine must be positioned so that
		the plug is accessible. Be sure to pull the plug off
receptacle. Be sure to use three-pins
		and close the water faucet in following cases:
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed		power failure, delivering the machine, setting the
reliably. Use leakage protector if possible.		machine idle or cleaning the machine. Do not plug
		or pull the power plug with wet hand.
	Earth

Do not bend ,extend,twist,bind by force.Do not press or nip it with weight. Keep the pin of the power plug clean,if the power plug is polluted with dust, please wipe with dry cloth carefully.

If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by the technicians of our special shop or our customer care agent.

In case the washing machine is installed on ground with	Do not use water hotter than 50 .
carpet, do not block the ventilation hole with carpet.

T h e v e n t i l a t i o n holes at the bottom

Soft object

Do not put the machine at damp place like	Do not wash water-proof laundries like
the bathroom. Never wash it with water. Do
	the raincoat, bike covers etc. to avoid
not put wet laundries on the control panel.
	abnormal vibrations in spinning.

Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more.

2

Trouble-shooting answer to question

(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.

Phenomena		The reason	How to settle
Buzzing upon reservation starts,
the digitron displays "E0"		The top lid is not closed	Close the top lid
No or slow drain, the digitron		Is the drain hose put down?	Put down the drain hose. Open
			and close the top lid once.
displays "E1" , buzzing.		Is the drain hose blocked by	Clean the foreign material.
		foreign material?
			Open and close the top lid once.
Running pauses during spin,		The top cover leaves open	Close the top lid
the digitron displays "E2",
buzzing
Safety switch actuates, not		Are the laundries put slantingly?	Re-order the laundries. Close the
spin, (after self-correction			top lid.Level the machine in right
		Is the machine slanting?	position.
twice), the digitron displays
			Open and close the top lid once.
"E3", buzzing
No or slow water filling (not		The water tap is not open	Open the water tap.
			Push the "Start/Pause" button.
reaching the level in 40 min),		The water inlet valve is blocked	Clean the water inlet valve.
the digitron displays "E4",		The water pressureis too low	Push the "Start/Pause" button.
			Wait for the normal water pressure
buzzing		and the current is too small
			Before use.
The digitron displays E6.		The water level sensor is bad.	Please contact the after-sales
			service department.
Poor or no waterfall flow		If the nozzle is choked with	Remove the foreign bodies
		foreign bodies
		Is there power failure?	Use it when the power is on.
	Not wash	Is the power plug loose?	Insert the power plug tightly.
		Does the water level arrive at the	Affusion to the set water level.
The machine does
		set water level?
not act
		Is the power plug loose?	Insert the power plug tightly.
	Not spin	Is the top lid closed?	Close the top lid
		Are the laundries put orderly?	Put the laundries orderly.
There's abnormal sound inside the		Is the machine slanting?	Level the machine properly.
machine		Are the laundries slanting in	Re-order the laundries.
		spinning?
		Is the jointer screw of the water	Fasten the jointer screw
The water faucet leaks		inlet hose is loose or twisted
			properly.
		awry?

Common phenomena
Phenomena	Explanation
The spinning is intermittent when it starts.	Balance the laundries to avoid slanting.
The wash procedure pauses.	The cloth sensor is detecting , it will add water
	after about 48 senconds.
Select spin program, but it does not work.	The program is setting the drain time , certain
	period is needed before it starts spinning.
There may be some water flowing out of the	It is the water remained performance inspection
drain hose in the first use of the machine.	by the factory.