Haier XQG50-S1016 Abnormal Setting water level during, Never place heavy objects, e.g. a heating

Warning code

Warning	Abnorma item	Content of identification	Action to take	Checking position and
code				ask for help
		The water level can not	Warning and	Check if the water
		reach the reset water		pressure is low or stops
			stop running
		level within 5 minutes		supplying
E11	Water supply	The water level can not	Warning and	Check if the water
		reach the setting water		pressure is low or stops
			stop running
		level within 8 minutes		supplying
		The water level can not		Check if the water outlet
E12	Drainage	reach the reset level in	Warning and	of the drainage and
		8 minutes after drainage	stop running	adjust it and restart the
		starting		machine
E13	Water supply	The water is above the	Warning and	Ask the technician to
		warning level	stop running	repair
		The feedback signal do-	Warning and	Ask the technician to
E31	Motor	es not change in 8 minu-
			stop running	repair
		tes during the motor runs
	Water level is	The water is ablove the	Warning and	Check if the water outlet
EA3	abnormal in the	setting water level during		of the drainage and adjust
			stop running
	drying process	the drying process		it and restart the machine
		The water temperature	No heating and	Ask the technician to
EC1	Heater	unchanged in 10 minutes	washing with	repair
			cold water
EC2	Water tempera-	The drying sensor circuit	Warning and	Ask the technician to
	ture sensor	short cut or open	stop running	repair
EC3	Water level	The water level sensor	Warning and	Ask the technician to
	sensor	circuit short cut or open	stop running	repair
		Within 30 minutes of dry
EC4	The temperature	phase there is 5 minutes	Warning and	Ask the technician to
	of air vent	in which the temperature	stop running	repair
		is not increasing
EC5	The dry tempe-	The heater sensor circuit	Warning and	Ask the technician to
	rature sensor	short cut or open	stop running	repair
U01	Unlock the door	Can not unlock after 4	Warning and	Ask the technician to
		times try	stop running	repair
U02	Lock the door	Can not lock the door	Warning and	Ask the technician to
		after 4 times try	stop running	repair
U03	Spin lopsidedly	The judgement of un-	Spin low speed	Disperse the clothings
		balance is above 1000g	and cancel	evenly in the tube
			drying
U04	Unclose the door	The door is unclosed	Warning	Close the door
E22	The memory	EEPROM goes wrong	Warning	Ask the technician to
	function is failure			repair

Matters needing attention

3. Never place heavy objects, e.g. a heating	4. Do not wash foam rubber or simalar sponge
appliance or water container, on the top panel	materials.
of the washing machine.

5. Before washing, close zippers, buttons,	6. Do not open the detergent dispenser during
laces and repair damaged areas. Underwear	the wash cycle. Otherwise, the water will spilt
and amall items should be palced in a laun-	out from it and the detergent can not be wash-
dry bag or pillow slip. Do not wash clothes	ed out completely.
containing wire frames.

7. The door is fitted with a self-locking device	8. After washing, turn off the tap to prevent
and can be opend when it is under the safety	leaking; unplug the washing machine and
state ( water should be under the safe level;	wipe clean the lower part of the porthole.
temperature inside the drum should be less
than 55 ; the drum should do not run). Do
not open the door except above condition
otherwise the self-locking device will be
damaged and the operator will get hurt.

9. Keep the door slightly open when the wa-	10. The tumble dryer should not be used if
shing machine is not being used. Never cover	industraial chemicals have been used for
the machine a	cleaning
plastic sheet.
	11. The appliance must not be installed behind
	a lockable door, a sliding door or a door with
	a hinge on the opposite to that of the tumble
	dryer.

14 3