Manuals / Harman-Kardon / Home Audio / Stereo Receiver

Harman-Kardon 760, 660 owner manual Part No. CQX1A1393Z

Models: 660 760

1 42

Download 42 pages 1.09 Kb

Page 42

Image 42

8500 Balboa Blvd., Northridge, CA 91329 www.harmankardon.com

Part No. CQX1A1393Z

Page 42

Image 42

Harman-Kardon 760, 660 owner manual Part No. CQX1A1393Z

Contents

AVR 760/AVR AUDIO/VIDEO RECEIVERImportant Safety Information SAFETY INFORMATIONImportant Safety Instructions Handle the AC Power Cord GentlyDo Not Open the Cabinet Installation LocationCleaning Moving the UnitTABLE OF CONTENTS Audio Section INTRODUCTIONThank you for choosing a Harman Kardon product Surround ModesAudio/Video Inputs Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANELCONTROLS ENGLISHFRONT-PANELCONTROLS KLM N Navigation These buttons are used to navigate the AVR’s menus, including the menus for the tuner, the USB device, The Bridge II, the Network and Internet RadioREAR-PANELCONNECTIONS ENGLISHREAR-PANELCONNECTIONS REMOTE CONTROL FUNCTIONS ENGLISHREMOTE CONTROL FUNCTIONS Volume Control Press to raise or lower the volumeZone 2 Remote Control REMOTE CONTROL FUNCTIONSENGLISH Multichannel Audio INTRODUCTION TO HOME THEATERTypical Home Theater System Surround ModesSpeaker Connections Connecting Source Devices to the AVRCONNECTIONS SubwooferDigital Audio Analog AudioCONNECTIONS RS-232Serial Port Video ConnectionsAntennas Digital VideoSPEAKER PLACEMENT Front Speaker PlacementSubwoofer Placement GETTING STARTED Table 2 - Source Assignment WorksheetENGLISH GETTING STARTED source devices and assign them to one of the four numbered HDMI InputsSTEP TWO - Connect TV INSTALLATIONSTEP ONE - Connect Source Devices STEP THREE - Connect LoudspeakersSTEP ELEVEN - Install a Multizone System Connect IR Control Devices to the Zone 2 IR InputINSTALLATION STEP FOURTEEN - Program Sources Into the Remote STEP TWELVE - Plug in AC Power CordsSTEP THIRTEEN - Insert Batteries in Remote INSTALLATIONTo change the device type of a Source Selector To “learn” individual key codesINSTALLATION STEP FIFTEEN - Turn On the AVR 760/AVR 660 To delete a programmed or learned codeTo rename a key or device INSTALLATIONINITIAL SETUP Using the On-ScreenMenu SystemINITIAL SETUP Set Up SourcesAudio and Video Input Selection ENGLISH6-/8-ChannelInputs HDMI-EquippedMultichannel Disc PlayerINITIAL SETUP INITIAL SETUP ENGLISHThis can be useful for older cable television systems that broadcast channels in both analog and digital audio Dolby Volume Calibration Offset Volume ControlDolby Volume Table 3 - Dolby Volume SettingsMute Function Sleep TimerHeadphones Audio EffectsRDS Operation Using the TunerRDS Tuning RDS Display OptionsNOTES ON NETWORK SETUP USB PlaybackInternet Radio OPERATIONNetwork Playback Using Docking StationTable 4 - Using The Bridge RecordingTable 5 - Using The Bridge II in iPod Manual Mode iPod manual modeOPERATION Selecting a Surround Mode OPERATIONMemory TROUBLESHOOTING GUIDEProcessor Reset ENGLISHAppendix - Default settings APPENDIXTable A2 - Source Setting Defaults Table A2 - Source Setting Defaults - continuedAPPENDIX AM Tuner Section TECHNICAL SPECIFICATIONSFM Tuner Section Video SectionTECHNICAL SPECIFICATIONS ENGLISHEyeConnect is a trademark of Elgato Systems Part No. CQX1A1393Z