Harman-Kardon AVR 3000 owner manual Remote Control Functions, Direct Input, as the source

Remote Control Functions

JDirect Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys Hto select a station (See page 31 for more information on the tuner).

KTuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode but- ton Ihas been pressed or the Band button @on the front panel was held pressed so that the AUTO indicator Xis illuminated, pressing either of the buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the AUTO indicator Xis NOT illuminated, pressing these buttons will tune stations in single-step increments. (See page 31 for more information.)

LOSD Button: Press this button to activate the On Screen Display (OSD) system used to set up or adjust the AVR 3000’s parameters.

MMacro Buttons: Press these buttons to store or recall a “Macro”, which is a pre-programmed sequence of commands stored in the remote. (See page 37 for more information on storing and recalling macros.)

NTransport Buttons: These buttons do not have any functions for the AVR, but they may be programmed for the forward/reverse play opera- tion of a wide variety of CD or DVD players, and audio or video- cassette recorders. (See page 36 for more information on programming the remote.)

OSkip Up/Down Buttons: These buttons do not have a direct function with the AVR 3000, but when used with a compatibly pro- grammed CD or DVD changer they will change the tracks on the disc currently being played in the changer.

PRDS Select Button: Press this button to display the various messages that are part of the RDS data system of the AVR 3000’s tuner. (See page 32 for more information on RDS).

QPreset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR 3000’s mem- ory. When CD or DVD is selected using the Input Selector button 4, these buttons may function as Slow Fwd/Rev (DVD) or ”+10” (CD).

Clear Button: Press this button to clear incorrect entries when using the remote to directly enter a radio station’s frequency.

Memory Button: Press this button to enter a radio station into the AVR 3000’s preset memory. After pressing the button the MEMORY indicator Uwill flash; you then have five sec- onds to enter a preset memory location using the Numeric Keys H. (See page 31 for more information.)

Delay/Prev Ch.: Press this button to begin the process for setting the delay times used by the AVR 3000 when processing surround sound. After pressing this button, the delay times are entered by pressing the Set button Fand then using the ⁄/¤ buttons Dto change the setting. Press the Set button again to complete the process. (See page 21 for more information.)

›Button: Press this button to change a set- ting or selection when configuring many of the AVR’s settings.

Speaker Select: Press this button to begin the process of configuring the AVR 3000’s Bass Management System for use with the type of speakers used in your system. Once the button has been pressed, use the ⁄/¤ but- tons Dto select the channel you wish to set up. Press the Set button Fand then select the speaker type (see page 19 for more infor- mation.)

Spare Button: This button does not have any function for the operation of the AVR3000, but it can turn on/off the Multiroom system on other Harman Kardon AV-receivers with that fea- ture and the Sub-function on DVD players.

Volume Up/Down: Press these buttons to raise or lower the system volume.

TV/Video Button: This button does not have a direct function on the AVR 3000, but when used with a compatibly programmed VCR, DVD or satellite receiver that has a “TV/Video” function, pressing this button will switch between the output of the player or receiver and the external video input to that player. Consult the Owner’s Manual for your specific player or receiver for the details of how it implements this function.

SPL Indicator Select: This button acti- vates the AVR 3000’s EzSet function to quickly and accurately calibrate the AVR 3000’s output levels. Press and hold the button for three sec- onds and then release it. Note that the Test Tone will begin circulating, and the Program Indicator 2will change colors. During this sequence, EzSet will automatically adjust the output levels for all channels until they are equal, as shown by the Program Indicator lighting green for each channel. (See page 23 for more information on EzSet.)

6-Ch. Direct Input: Press this button to select the component connected to the 6-Ch.

Direct Input as the source

Mute: Press this button to momentarily silence the AVR 3000 or TV set being controlled, depending on which device has been selected.

When the AVR 3000 remote is being programmed to operate another device, this button is pressed with the Input Selector button 4to begin the programming process. (See page 36 for more information on programming the remote.)

NOTE: As any of the remote buttons pressed is active with the device selected, the correspon- ding Selector button 45will briefly flash red to confirm your selection.

REMOTE CONTROL FUNCTIONS 13