Harman-Kardon Comprehensive EzSet EQ Setup Guide for Harman Kardon Receivers

AVR

Set Up the AVR

ENGLISH

5.Press the remote control’s AVR button. The AVR’s on-screen display (OSD) Main Menu screen will appear on the TV.

Source Select

Select the Source Device

Setup Source

Setup Source Devices

Speaker Setup

Speaker Optimization, EQ

Zone 2

Manage and Control Zone 2

System

General AVR Settings

Settings Lock

Manage System Lock

6. Use the remote’s Up/Down/Left/Right and OK buttons to select “Speaker Setup.”

Speaker Setup

Automatic Setup – EzSet/EQ

Automated Speaker Setup and EQ

Manual Setup

Manually Adjust Speaker Settings

7. Select “Automatic Setup – EzSet/EQ” and then select “Continue.”

Set Up Your Sources

The Setup Source menu lets you assign the correct physical audio and video connections to each source and lets you set many audio and video playback features for each source.

IMPORTANT: The “Video Input from Source,” “Audio Input from Source” and “Resolution to Display” settings are not optional and must be adjusted before you use your AVR to enable playback of each source. You can adjust the other settings later. See System Settings, on page 39, for complete information about adjusting all of the Settings menu options.

1.Review the assigned connectors you listed on the Source Buttons and Assigned Connectors table, on page 18. Note what changes (if any) you want to make from the default source-button connector assignments that appear on the list. (If there are no changes, you can skip this section.)

2.To display the Source Settings menu for the active source, press the Info button on the front panel or remote. Or, from the Main Menu screen, select “Setup Source” and select a source from the slide-in menu. The Settings menu for that source will appear.

Cable/Sat

Audio Effects

Video Modes:	Off
Surround Modes:	Auto Select
Audio Format from Source:	NO AUDIO INPUT
Video Input from Source:	HDMI 2
Audio Input from Source:	HDMI 2
Resolution to Display:	720p – 60Hz
Resolution from Source:	No Input
HDMI Bypass:	Off
Change Name:	Cable/Sat
Adjust Lip Sync

3.Select “Video Input From Source” and select the video input connector you want to assign to the source button. Press the OK button. NOTE: If you select an HDMI connector as the Video Input from Source, the Audio Input from Source will automatically change to the same HDMI connector. If you want to use a different audio connection, proceed to step 4.

8. Select the number of speakers in your system. Select “5.1” if no surround back or

front height speakers are present or if you will be using the Assigned Amp channels

for multizone operation.

9. The test will begin. Make sure that the room is quiet while the test noise is playing

through the speakers.

10. When the test finishes, select “Continue,” then select “View Settings” to see the

results of the EzSet/EQ process, or select “Done” to exit.

NOTES:

ssIf there are fewer than five main speakers in your system, do not use the EzSet/ EQ process. Instead, proceed as described in Manual Speaker Setup, on page 36.

Cable/Sat

Audio Effects

Video Modes:	Off
Surround Modes:	Auto Select
Audio Format from Source:	No Audio Input
Video Input from Source:	HDMI 2
Audio Input from Source:	HDMI 2
Resolution to Display:	1080p – 60Hz
Resolution from Source:	No Video Input
HDMI Bypass:	Auto
Change Name:	Cable/Sat
Adjust Lip Sync

HDMI 1

HDMI 2

HDMI 3

HDMI 4

HDMI 5

HDMI 6

HDMI 7

HDMI Front

Component

Composite 1

ssIf you are using a 6.1-channel configuration with a single surround back speaker, use EzSet/EQ automatic configuration for 5.1 speakers, connect the single surround back speaker to the left Assigned Amp Speaker Output connector, then configure the surround back speaker manually, as described in Manual Speaker Setup, on page 36.

Zone 2 Audio: Analog 1

27