AVR

Advanced Remote Control Programming

Remote Channel-Control Punch-Through

The punch-through feature allows you to operate one component while setting certain groups of controls to operate another component. For example, while using the AVR controls for surround modes and other audio functions, you may also use the remote to operate the transport controls of your Blu-ray Disc player. Or while using the remote to control video functions on your TV, you may also use the remote to change channels on your cable box.

To program punch-through control while operating any device:

1.For three seconds press and hold the Source Selector button for the main device the remote will be operating. The Source Selector will light up, go dark and then light up again, indicating the remote is in Program mode and that you may release the button.

2.Select the type of punch-through programming.

a)For channel-control punch-through, press the Channel Up button.

b)To program transport-control punch-through, press the Play transport-control button.

3.Press the Source Selector button for the device whose channel or transport controls you will use while operating the device selected in the first step. The Source Selector button will flash to confirm.

For example, to watch the TV while changing channels using the cable box, press and hold the TV button until it lights. Then press the Channel Up button, followed by the Cable/ SAT button.

To undo punch-through programming, follow the same steps as above, but press the same Source Selector button in Steps 1 and 3.

NOTE: The Volume and Mute controls are always dedicated to the AVR.

Programming Macro (Activity) Commands

In addition to their normal functions, you can also use the 0 – 9 Number buttons and AVR Power On button to store Macro (Activity) commands – up to 11 of them. Each Macro can send out up to 19 commands at one time from a single button push. Any AVR remote control button’s function from any mode (except the Back/Exit button, the Light button, and the Activity button) can be programmed into a Macro.

NOTE: Use caution when programming complicated Macros. It isn’t possible to program a pause or delay before sending additional commands after a “Power On” command, and the component may not be ready to respond to commands immediately after powering on.

To program a Macro:

1.To enter the Programming mode, simultaneously press and hold the Activity button and the Number button or AVR Power On button to which you want to assign the Macro.

2.Press in up to 19 commands that you want stored in that Macro button. During each successive button selection, the Source Selector button LED will blink once. Press the Source Selector button for each device (or Setup button for the AVR itself) before you enter individual commands. This step counts as one of the 19 commands allowed for each Macro.

ssYou can select functions from another mode by first pressing the corresponding Source Selector button and then the buttons where those functions are located within that mode. Pressing a Source Selector button also counts as one command.

ssFor power on, press the AVR or Device Power On button.

ssFor power off, press the AVR or Device Power Off button.

3.Press the Activity button to end the programming process. The last Source Selector button (or the Setup button) will flash three times.

It isn’t possible to “edit” a command within a Macro. To erase the Macro:

1.Press and hold the Activity Button and the button into which you programmed the Macro until the Source Selector or Setup button lights up.

2.Press the Activity button to erase the Macro.

To execute a Macro:

Press the Activity button, then press the button into which you programmed the Macro.

IMPORTANT: Keep the remote aimed at the components until all of the Macro commands have been executed. The remote can take up to 10 seconds to send out 19 Macro commands.

Advanced Remote Control Programming

Recording

Two-channel analog audio signals, as well as composite video signals, are normally available at the appropriate recording outputs. To make a recording, connect your audio or video recorder to the appropriate AVR output connectors as described in the Making Connections section, insert blank media in the recorder and make sure the recorder is turned on and recording while the source is playing. Refer to the recording device’s instructions for complete information about making recordings.

NOTES:

1.The AVR only records analog audio signals. It does not convert digital audio signals to analog.

2.HDMI and component video sources are not available for recording.

3.Please make certain that you are aware of any copyright restrictions on any material you record. Unauthorized duplication of copyrighted materials is prohibited by law.

Sleep Timer

The sleep timer sets the AVR to play for up to 90 minutes and then turn off automatically.

Press the Sleep button on the remote, and the time until turn-off will be displayed. Each additional press of the Sleep button increases the play time by 10 minutes, with a maximum of 90 minutes. The SLEEP OFF setting disables the sleep timer.

When the sleep timer has been set, the front-panel display will automatically dim to half brightness.

If you press the Sleep button after the timer has been set, the remaining play time will be displayed. Press the Sleep button again to change the play time.

Resetting the Remote

To reset the remote to its factory default condition, simultaneously press and hold the TV Source Selector button and the “0” Number button. When the TV Source button relights, enter the code “333.” When the TV button goes out, and all of the Source Selector buttons flash, the remote control will be reset.

Processor Reset

If the AVR behaves erratically after a power surge, first turn off the rear-panel Main Power switch and unplug the AC power cord for at least 3 minutes. Plug the cord back in and turn the receiver on. If this procedure doesn’t help, reset the AVR’s processor as described below.

NOTE: A processor reset erases all user configurations, including video resolution, speaker and level settings, and tuner presets. After a reset, reenter all of these settings from your notes in the Appendix worksheets.

To reset the AVR’s processor:

1.Press the front-panel Standby/On switch to place the unit in the Standby mode (the Power Indicator will turn amber).

2.Press and hold the front-panel Surround Modes button for at least 5 seconds until the RESET message appears on the front-panel Message Display.

NOTE: After performing a processor reset, wait at least 1 minute before pressing any Source Selector buttons.

If the receiver does not function correctly after a processor reset, contact an authorized Harman Kardon service center for assistance. Authorized service centers may be located by visiting our Web site at www.harmankardon.com.

44

Page 43 Page 45
Page 44
Image 44
Harman-Kardon AVR 3700 Advanced Remote Control Programming, Recording, Sleep Timer, Resetting the Remote, Processor Reset
Page 43 Page 45

AVR 2700, AVR 3700 specifications

The Harman-Kardon AVR 3700 and AVR 2700 are high-performance audio-video receivers that offer impressive features and technologies for home theater enthusiasts. Designed for those who value both sound quality and versatility, these models stand out with their powerful amplifications and comprehensive connectivity options.

The AVR 3700 boasts a 7.2-channel architecture, delivering a robust audio experience with a total output of 100 watts per channel. It supports the latest surround sound formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring a cinematic audio experience that is both immersive and detailed. With Harman-Kardon's proprietary DSP algorithms, users can enjoy dynamic sound staging and precision sound imaging.

The AVR 2700, while slightly less powerful with its 7.1-channel setup, still provides 80 watts per channel and supports similar advanced audio formats. It offers excellent sound quality, making it an ideal choice for users who may not require the higher output levels of the AVR 3700.

Both models incorporate advanced HDMI technology, with multiple HDMI inputs and outputs that support 4K video pass-through, allowing seamless integration with modern 4K televisions and other high-definition sources. The AVR 3700 includes up to eight HDMI inputs, while the AVR 2700 features six, providing ample connectivity for streaming devices, gaming consoles, and Blu-ray players.

Furthermore, the Harman-Kardon receivers come equipped with AirPlay and Bluetooth for easy wireless streaming. This allows users to play their favorite music directly from smartphones, tablets, or computers without the hassle of cables. Both models also support DLNA, enabling access to networked audio files.

Another key feature of both receivers is the MultEQ room calibration technology. This sophisticated system analyzes the room’s acoustics and adjusts the receiver’s audio output accordingly, optimizing sound quality for various listening environments.

The AVR 3700 and AVR 2700 also feature intuitive user interfaces, making it easy to navigate settings and options. A user-friendly remote control, along with mobile app compatibility, further enhances the overall experience.

In summary, the Harman-Kardon AVR 3700 and AVR 2700 represent excellent choices for anyone seeking to elevate their home entertainment system. With their powerful audio capabilities, extensive connectivity options, and advanced audio technologies, these receivers are engineered to provide a rich and engaging audio-visual experience. Whether you’re watching movies, listening to music, or gaming, both models ensure that every sound is delivered with clarity and precision.
Top Page Image Contents