Harman-Kardon AVR 2700 owner manual Wired Network Setup, Wireless Network Setup AVR 3700/AVR

AVR

Wired Network Setup

If your network uses an automatic IP address, you should not have to perform any network setup procedures for a wired network connection. Once you connect the AVR to your home network, the network should automatically assign the AVR an IP address, and the AVR should automatically connect to your network.

If your AVR does not automatically connect to your network (in which case the AVR will display a “Not Connected” message when you press the Network source button):

1.Press the AVR button, select System, then select Network Settings. The Wired/Wireless selection screen will appear.

2.Select Wired. The Wired Network Settings menu will appear.

Network Settings

Mac	0x:00:0x:00:0x:0x
Network Settings:	Automatic
IP Address:	000 . 000 . 000 . 000
Subnet Mask:	000 . 000 . 000 . 000
Gateway:	000 . 000 . 000 . 000
Primary DNS:	000 . 000 . 000 . 000
Secondary DNS:	000 . 000 . 000 . 000
Proxy	Off
IP Address:	000.000.000.000
Proxy Port:	00000
Network Status:	Connected
Apply & Save

3.Select Network Settings, the press the OK button twice to cycle the setting from “Automatic” to “Manual” and back to “Automatic.”

4.Select Apply & Save. The AVR will attempt to connect to the network.

5.If the AVR again fails to connect to the network, you may need to enter your network’s settings manually. See Network Settings (under General AVR Settings), on page 40, for complete instructions. You may need to obtain your network’s settings from your ISP or network administrator.

NOTE: We recommend that you directly connect the AVR to a home-network router so that it can directly access the Internet for Internet radio, or access a PC on the network for playback of content stored on the PC (see Listening to Media via Your Home Network, on page 32, for more information).

Wireless Network Setup (AVR 3700/AVR 370)

If you want to join the AVR to your Wi-Fi network you will need to perform the following setup procedure.

1.Press the AVR button, select System, then select Network Settings. The Wired/Wireless/ Network Upgrade selection screen will appear.

2.Select Wireless. The Wireless Network Settings menu will appear.

Network Settings

Search AP

Information

iPod Network Setup

AVR AP Mode

Set Up the AVR

The following options appear in the Wireless Setup menu:

ssSearch AP: Select this option to display and select the wireless network you wish to join.

ssInformation: Select this option to display the settings information for the active wireless network. This screen is informational only – you cannot make changes in the network settings from it.

ssiPod Network Setup: Selecting this option lets you use your portable device with iOS 5 or later to automatically have the AVR join the same wireless network to which the device is already connected. See Using your iOS 5 device to join the wireless network, below, for details.

ssAVR AP Mode: This option provides an alternate method for connecting to a wireless network without using the AVR’s on-screen display.

NOTE: If you have already made a connection to a wired network you will not be able to select the Wireless setting. Disconnect the AVR from the wired network and begin again at Step 1.

3.Select Search AP and select the network you wish to join from the ones displayed. The Enter Password screen will appear.

4.Use the remote’s up and down arrow buttons to select each character in your Wi-Fi network’s password. (The characters will appear on the AVR’s front-panel display and the OSD screen.) When you have selected the correct character, use the right arrow button to move to the next one. If you make a mistake, use the left arrow button to change a previous character.

5.Once the correct password is displayed on the AVR’s front-panel display and the OSD screen, press the OK button. The AVR will attempt to join the network.

6.When the AVR has successfully joined the network it will display “Connection Success” on its front-panel display and OSD.

ssIf the AVR is not able to join the network it will display “Connection Failure.” If this happens, confirm that you entered the correct password, attempt to connect to another wireless network or make a wired network connection.

Using your iOS 5 device to join the wireless network:

1.Make sure that your iOS 5 device is joined with the wireless network you want the AVR to join.

2.Connect your iOS 5 device to the AVR’s front-panel USB port.

3.The iPod Network Setup option described in Step 2, above, will become available. Select it.

4.The AVR will automatically join the network without requiring further input from you.

ENGLISH

29