Wall-Mounting: Center Speaker
1.Decide on the location for the speaker (see Speaker Placement, on page 5).
2.Attach the center speaker
Use These Holes to Attach Bracket to Wall
NOTE: The center speaker weighs 3.2 lb (1.45kg). Be sure to use hardware that can support this weight.
CAUTION: Before making speaker connections, be sure that your receiver or amplifier is turned OFF and preferably, its AC cord is unplugged from the AC power source.
3.Connect the speaker wire to the speaker terminals. Press down on the top of the terminal to open the connection hole, insert the wire’s bare end all the way into the hole and release the terminal to secure the wire. Insert the conductor with the colored band into the speaker’s red ( + ) terminal, and insert the other conductor into the speaker’s black ( – ) terminal, as shown in the illustration.
A. Push Down on Cap to | B. Insert Bare Wire into | C. Release Cap to Secure Wire |
Open Hole | Open Hole |
|
Speakers and receivers/amplifiers have corresponding ( + ) and ( – ) connection terminals. Most electronics manufacturers, including Harman Kardon, use red to denote the ( + ) terminal and black for the ( – ) terminal. Newer Harman Kardon receivers conform to the CEA standard and therefore use a color other than red to denote the ( + ) terminal for some speaker positions. See the table in
Each speaker wire included with your system has colored bands at both ends of the ( + ) conductor, and the subwoofer cable has purple connectors that correspond to the color of the HKTS200SUB’s LFE jack. This system helps ensure that the speaker in each location is connected to the correct receiver or amplifier terminals. In addition to the colored bands at each end, each speaker wire’s ( + ) terminal has ribs molded into its insulation to help identify it.
It is very important to connect each speaker identically: ( + ) on the speaker to ( + ) on the receiver or amplifier, and ( – ) on the speaker to ( – ) on the receiver or amplifier. Miswiring one or more speakers results in thin sound, weak bass and a poor stereo image. With the advent of multichannel
To connect the speaker wire to the terminals on the satellite and center speakers, press down on the top of the terminal to open the connection hole, insert the wire’s bare end all the way into the hole and release the terminal to secure the wire. Insert the conductor with the colored band into the speaker’s red ( + ) terminal, and insert the other conductor into the speaker’s black ( – ) terminal, as shown in the illustration.
ENGLISH
+ | – |
|
| – |
|
|
|
| + |
| |
|
|
|
|
| |
Important: Make sure the ( + ) and ( – ) bare wires do not touch each other or the | A. Push Down on Cap to | B. Insert Bare Wire into | C. Release Cap to Secure Wire | ||
Open Hole | Open Hole |
|
| ||
other terminal. Touching wires can cause a short circuit that can damage your receiv |
|
|
|
| |
er or amplifier. |
| IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or the | |||
4. Using two of the supplied screws, attach the center speaker to the | other terminal. Touching wires can cause a short circuit that can damage your receiver or | ||||
amplifier. |
|
|
| ||
bracket, as shown in the illustration. |
|
|
|
| |
|
|
|
|
| |
Connecting Satellite Speakers With Supplied
Follow the instructions in
Wall-Mounting: Center Speaker, opposite.
Connecting Satellite Speakers with Supplied Bases
| 1. | Remove the speaker’s base (see Shelf Placement, on page 5). |
| 2. | Pass the speaker wire through the opening in the speaker base. |
3. | Connect the speaker wire as described above. | |
|
| |
Bracket | 4. | Reattach the speaker’s base as shown in the illustration. |
Supplied Screws
Speaker Connections
CAUTION: Before making speaker connections, be sure that your receiver or amplifier is turned OFF and preferably, its AC cord is unplugged from the AC power outlet.
7
