PROGRAMMING THE REMOTE
3. Press the Input Selector ebutton chosen and the Learn Button 
41 at the same time. Hold these buttons until the Program/SPL Indicator cflashes amber and the light under the device selector button turns red. Release the buttons.
4.Press the button on the RCP 2 that you wish to program. The Program/SPL Indicator cwill stop flashing.
5.Within 5 seconds, press and hold the button on the original remote that you wish to “teach” into the RCP 2. When the Program/SPL Indicator cturns green three times, release the button. The Program Indicator will then begin to flash amber again.
NOTE: If the Program/SPL Indicator cturns red during Step 4 or 5, the programming was not successful. Repeat the steps to see whether the code will “take.”
6.Repeat Steps 4 and 5 for each button on the source remote that you wish to transfer to the RCP 2 remote.
7.Once all codes have been transferred from the
original source remote to the RCP 2, press the Learn Button 
41 .
8.Repeat Steps 1 through 7 for any additional remotes you wish to “teach” into the RCP 2.
Erasing Learned Codes
The RCP 2 allows you to remove or erase the code learned into a single button for a single device, to remove or erase the code set for all the codes that have been programmed into specific device buttons, or to erase all commands that have been learned to all devices.
If you erase a code that is part of a macro, that macro sequence will no longer operate properly.
To erase a single learned code from within a single device’s settings, follow these steps:
1.Press and hold both the Input Selector ef
within which the individual button to be erased has been programmed and the Learn Button 
41 .
2.When the red LED under the Input Selector turns red and the Program/SPL Indicator cflashes amber, release the buttons.
3.Press and release the Input Selector ef again for the device within which the individual button to be erased has been programmed.
4.Press the 7 Button rfour times.
5.Press and release the individual button for which the code is to be erased. The Program/SPL Indicator cwill blink green twice and then return to amber.
6.To erase other buttons within the same device, press them as described in Step 5.
7.When all buttons to be erased have been pressed,
press the Learn Button 
41 to complete the process.
To erase all codes within a single device, follow these steps:
1.Press and hold both the Input Selector ef for which you wish to erase the codes and the
Learn Button 
41 .
2.When the red LED under the Input Selector turns red and the Program/SPL Indicator cflashes amber, release the buttons.
3.Press and release the Input Selector ef again for the device whose codes you wish to erase.
4.Press the 8 Button rfour times.
5.The Program/SPL Indicator cwill turn off and the red light under the Input Selector will flash on and off once to indicate that the codes have been erased.
To erase all codes that have been programmed to all devices in the remote, follow these steps:
1.Press any Input Selector effor which
you wish to erase the codes and also the Learn Button 
41 .
2.When the red LED under the Input Selector turns red and the Program/SPL Indicator cflashes amber, release the buttons.
3.Press and release the Input Selector ef again for the device whose codes you wish to erase.
4.Press the 9 Button rfour times.
5.The Program/SPL Indicator cwill turn off and the red light under the Input Selector will flash on and off once to indicate that the codes have been erased.
Macro Programming
Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the RCP 2. Once programmed, a macro will send out up to 19 different remote codes in a prede- termined sequential order, enabling you to automate the process of turning on your system, changing devices, or other common tasks. The RCP 2 can store up to five separate macro command sequences: one that is associated with the Power On Button dand four more that are accessed by pressing the Macro Buttons 30 .
1. Press the Mute Button 
43 and the Macro Button 30 to be programmed or the Power On Button dat the same time.
An Input Selector will light red, and the Program/ SPL Indicator cwill flash amber.
2.Enter the steps for the macro sequence by press- ing the button for the actual command step. Although the macro may contain up to 19 steps, each button press, including those used to change devices, counts as a step. The Program/SPL Indicator cwill flash green to confirm each button press as you enter commands.
NOTE: While entering commands for Power On/Off of any device during a macro sequence, press the Mute Button 
43 . DO NOT press the actual Power button.
3.When all the steps have been entered, press the Sleep Button j to enter the commands. The red light under the Input Selectors ef will blink and then turn off.
Example: To program the Macro 1 button so that it turns on the AVR, TV and a cable box, follow these steps:
•Press the Macro 1 Button 30 and Mute
Button 
43 at the same time and then release them.
•Note that the Program/SPL Indicator cwill flash amber.
•Press the AVR Selector f.
•Press the Mute Button 
43 to store the AVR’s power on command.
•Press the VID 3 Input Selector Button eto indicate the next command is for “TV Power On.”
•Press the Mute Button 
43 to store the TV Power On Command.
•Press the VID 2 Input Selector Button eto indicate the next command is for “Cable Power On.”
•Press the Mute Button 
43 to store the Cable Power On command.
•Press the Sleep/Channel Up Button jto complete the process and store the macro sequence.
After following these steps, each time you press the Macro 1 Button 30 the remote will send the Power On/Off command.
8 PROGRAMMING THE REMOTE
