Manuals / Hayter Mowers / Lawn and Garden / Trimmer

Hayter Mowers 407F manual Use The Trimmer Head, Drive Lever, Use The Throttle Control, Operation

Models: 407F

1 30

Download 30 pages 43.15 Kb

Page 12

USE THE TRIMMER HEAD

OPERATION
USE THE TRIMMER HEAD
DRIVE LEVER
1. To engage the trimmer head, hold the con-	Control Bail
1. To engage the trimmer head, hold the con-	Handlebar
trol bail against the handle. Move the
trimmer head drive lever forward to en-
gage the trimmer head. See Figure 6. The
faster the engine runs, the faster the trim-
mer head will rotate.
2. Once the trimmer head is rotating, push
the machine forward to trim.
	Trimmer Head
	Drive Lever
	Figure 6

USE THE THROTTLE CONTROL

1.During normal use, set the throttle con- trol lever in the FAST position to run the engine at full speed.

2.Pull the throttle control lever back to de- crease engine speed. Push the throttle control lever forward to increase engine speed.

3.To stop the engine, pull the throttle con- trol lever completely back to the STOP position.

Throttle Control

Lever

Figure 7

USE THE PRIMER BUTTON

1.Push the primer button. See Figure 8 for location. For the number of times to push the primer button, see the primer button decal located on the engine or follow the directions in the Engine Manual. Wait approximately two seconds between each push.

NOTE: Do not use the primer button to re- start a warm engine after a short shutdown.

Primer

Button

Figure 8

1739579

12

Image 12

Hayter Mowers 407F manual Use The Trimmer Head, Drive Lever, Use The Throttle Control, Use The Primer Button, Operation

Contents

Code 407F POWERTRIMOWNER’S HANDBOOK TABLE OF CONTENTS LIMITED WARRANTYOPERATOR SAFETY ASSEMBLYLIMITED WARRANTY HAYTER LIMITEDOPERATOR SAFETY SAFETY PRECAUTIONSOWNER’S INFORMATION The responsibility of the owner is to follow the instructions belowIV. Service II. Slope OperationIII. Children OPERATOR SAFETYOPERATOR SAFETY 12. Clean and replace safety and instruction decals as necessarySafety Warning Pictorials INTERNATIONAL PICTORIALSControl And Operating Pictorials OPERATOR SAFETYASSEMBLY CONTENTS OF LITERATURE PACK1 - Warranty Card 1 - Safety Glasses 1 - Trimmer Line 2 Sets REMOVE THE TRIMMER FROM CARTONRAISE THE HANDLE ATTACH THE GUARDASSEMBLY CHECKLIST ENGINE PREPARATIONFill Crankcase With Oil Fill Fuel Tank With PetrolKNOW YOUR POWERTRIM OPERATIONEYE PROTECTION STOP THE TRIMMER HEADUSE THE TRIMMER HEAD DRIVE LEVERUSE THE THROTTLE CONTROL USE THE PRIMER BUTTONSTART THE ENGINE TRIMMER TIPSOPERATION MAINTENANCE SERVICE RECORDScomplete regular service Fill in dates as youLUBRICATION Lubricate the Jackshaft Assembly Change Engine OilMAINTENANCE ADJUST THE HEIGHT OF THE HANDLEBAR SPARK PLUGMAINTENANCE SERVICE AND ADJUSTMENT PROPER CARE OF TRIMMER LINECHANGE TRIMMER LINES MAINTENANCEREPLACE THE DRIVE BELT STORAGETrimmer EngineTROUBLESHOOTING CHART TROUBLECAUSE CORRECTIONTROUBLESHOOTING CHART Engine overheatsEngine will not stop runningEngine Power Rating Information SPECIFICATIONSthis Series engine Order Replacement Parts Repair Parts POWERTRIM Code 407F specification chartHandle And Wheels NOTE Unless noted otherwisePOWERTRIM Code 407F Handle And WheelsREF NO QTY. DESCRIPTIONPOWERTRIM Code 407F specification chartCutting Head And Shield NOTE Unless noted otherwisePOWERTRIM Code 407F Cutting Head And ShieldREF NO DESCRIPTIONTorque Specification Chart Hardware Identification & Torque SpecificationsNut, 1/2” Screw, 1/2