Hayter Mowers RS 17/102H Assembling the grass box, Assembling the grass box on the tractor

GB

Assembling the grass box

19	Place the lower part of the frame on a suitable base (e.g. a
	table).

20	Screw the upper part of the frame onto the lower part of the
	frame on both sides.
	M 6 x 35 hexagonal head screw	(4 x)
	Ø 6 x Ø 18 shim	(4 x)
	Ø 6 x Ø 12 shim	(4 x)
	M 6 self-locking nut	(4 x)
	Attention!
	Only tighten the nuts by hand to start with due to the
	subsequent fixing of the box fabric.
	Fit shim Ø 6 x Ø 18 under the screw head!
	Screw the transverse tube o onto the box frame.
21	M 6 x 45 hexagonal head screw	(2 x)
	Ø 6 x Ø 12 shim	(4 x)
	Ø 6 curved shim	(2 x)
	M 6 self-locking nut	(2 x)
	Place the frame onto the box base of the fabric sack.
	Attention:
22
	The ribs of the box base pointing upwards.
	Clip the fabric sack onto the box frame.
	Remove the upper frame screw connection and screw the
	fitting flap of the fabric sack together with the upper and
23	lower part of the box frame.
	Fit the Ø 6 x Ø 18 shim under the screw head.
	Carry out this procedure on both sides.
	Clip the stopper n into the opening on the right-hand
	side of the box lid.
24
	Screw the contact elbow o for the box switch onto the
	box lid.
	Ø 6 x 25 counter-sunk screw	(2 x)
	Attention!
	Make sure that the position of the contact elbow is as
	shown.
	Screw the box handle n onto "superstructure left" o
25	and "superstructure right" p.
	M 8 x 60 screw	(2 x)
	Ø 8 x Ø 15 shim	(2 x)
	shim	(2 x)

Attention!

The connection contours of the two superstructures must correspond with the outer contour of the box lid.

26	Screw the box handle onto the box lid
	M 6 x 20 screw	(2 x)
	Ø 6 x Ø 12 shim	(2 x)
	Ø 6 x Ø 18 shim	(2 x)
	M 6 self-locking nut	(2 x)
	Position the box lid and screw onto the box frame
27	M 6 x 40 hexagonal head screw	(5 x)
	Ø 6 x Ø 18 shim	(5 x)
	Ø 6 x Ø 12 shim	(5 x)
28
	M 6 self-locking nut	(5 x)
	Holder	(2 x)
	Attention!

Fit the Ø 6 x 18 shim under the screw head.

Push the box strut (Ø 8 mm) through the base of the box and the lower part of the frame.

Attention!

The box strut must protrude by the same distance on both sides of the box.

Thread the gas spring onto the box strut in the order

29 shown and screw tight. Carry out this procedure on both sides.

n Ø 12 x 13 spacer bushing	(2 x)
o Gas-pressure spring	(2 x)
p Ø 8 x Ø 15 shim	(2 x)
q M 8 self-locking cap nut	(2 x)

Attention!

Only tighten the cap nuts to such an extent that the gas- pressure springs can still be pivoted

Assembling the grass box on the tractor

30	Hold the grass box by the box handle in one hand. With the
	other hand - gently pressing onto the box lid - position the
	upper part of the frame onto the box holding arms and push
	forwards until the grass box engages in the bearings.
	Attention!
	The arrows on the box lid and the seat console must
	match.
31	If the gap between the box lid and the seat console is too
	large, the box holding arms can be adjusted by loosening
	the screws in the directions shown
	Push the forkhead n of the gas-pressure spring across the
32
	fitting lug o of the back wall until the bores are flush.

Push the securing bolts p through the forkhead and the lug and lock them.

Carry out this procedure on both sides.

GB 12